Ariston MARGHERITA, Instructions For Installation And Use Manual

Page: 20 / 32

M
ARGHERITA
Margherita - Instructions for installation and use
E
A
B
C
D
F G
Mode Select
Here I’m in command
Understanding the control panel
Making the right choice is important. And it’s easy.
Margherita’s knobs
are hidden. Just
press them lightly in
the middle to
extract them.
The detergent dispenser with
the additional bleach
compartment is here.
17
MAX
1
2
4
3
This option is available on all wash
programmes except for number 10
and Drain .
Wash intensity
This allows you to modify the
characteristics of the selected wash
programme, according to how soiled
the washing is. There are three levels;
press the select button to Select
them.
Low
Medium
High
This option is available on
programmes 1-2-3-5-6-7 .
Delay timer
This allows you to delay the start of
the wash cycle by a minimum of 1
to a maximum of 24 hours by
pressing the Select button.
The enabling of the delayed start is
indicated by the symbol coming
on and staying on until the wash
cycle begins.
This option is not available on the
Drain and Light Spin programmes.
Stain removal (see page 21)
Thanks to this command, the washer-
dryer will carry out a more intensive
wash that optimises the effectiveness
of the liquid additives, thus allowing
more resistant stains to be removed.
To use this, press the Select button
until the On sign comes on.
During a wash cycle, the selectionof
this option is indicated by symbol
coming on.
This option is available on
programmes 2-3-5-6-7-9 and Light
Rinse .
Note : It must not be used with the
Easy iron option.
Programme selector knob
To select a programme, you should
turn the knob so that the symbol/
number of the desired programme is
in line with the pointer on the glass G .
On-off
When button B is pressed, the
washer-dryer is switched on, when
it is not the machine is switched off.
Turning the appliance off
does not cancel the selected
programme.
When the appliance is switched on,
all the symbols on the display light
up for at least 8 seconds, after
which only the ones that can be
selected will flash.
Start /Reset
This button allows you to start the
selected wash programme or to
interrupt it.
If you press it briefly, the button
functions as Start , if you press it
for at least 3 seconds, then it
functions as Reset .
After the Start of the appliance,
moving the programme selector
knob will have no effect
whatsoever.
Detergent dispenser
It is divided into three
compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle wash;
3. Fabric conditioner.
The washer-dryer is equipped with
an extra compartment 4 (provided
as an accessory) for the bleach, to
be inserted in compartment 1 .
Programme key
This contains the descriptions of the
wash programmes and the various
functions connected to the buttons.
Pull it outwards to open it.
Display
All the options available are
displayed on the right-hand side.
Use the Mode button to select the
desired option, and the relative
symbol will begin flashing.
On the left-hand side, the value or
the status ( On-Off ) of the selected
option is displayed, and you can
modify it using the Select button.
To access the subsequent option,
press the Mode button, otherwise
press button C (Start/Reset) to start
the wash cycle.
All the options available are listed
below.
Only options relevant to the
selected programme will be
displayed.
Temperature
The display indicates the maximum
temperature relating to the
programme set, which can be
reduced by pressing the Select
button right down to cold wash ( Off ).
This option is available on all wash
programmes.
Spin variation
The display indicates the maximum
speed relating to the programme set,
which can be reduced by pressing the
Select button right down to its total
exclusion ( Off ).
You may not select a drying
cycle if you have excluded the
spin cycle.
During a wash cycle, the selection
of the spin cycle exclusion is
indicated by symbol coming on.
Easy iron
This function allows your washing
to come out of the machine without
creases, making it much easier to
iron .
The appliance optimises the
washing conditions according to the
type of fabrics that are being
washed.
It is enabled with programmes 3-5-
6-7-10 and Light Rinse .
To enable it, press the Select button
until the On sign comes on.
In programmes 6-7-10 and Light
Rinse , the wash cycle is
interrupted and the washing is left
to soak in water before the
appliance is drained. To complete
the cycle, press the Select button.
During a wash cycle, the enabling
of this option is indicated by symbol
coming on.
Note :
- It must not be used with the Stain
removal option.
- If you also want to run the drying
cycle, this button is enabled only
if combined with level ( Iron ).
Rinse level
This increases the efficiency of the
rinse. We recommend that you use
it when dealing with a full load and
a great amount of detergent.
There are three levels; press the
Select button to select them.
Low
Medium
High
This option is available on
programmes 1-2-3-4-5-6-7 and
Light Rinse .
Drying
This allows you to set the automatic
drying at the end of the wash.
For further details, please refer to
page 19.
Warning: If you set "spin cycle
exclusion", you may not select a
drying cycle.
If you wish to run a drying cycle,
select the maximum spin speed
available and then choose the type
of drying required.