ARISTON DISHWASHER - Instructions for installation and use
15
D
ISHWASHER
First of all.
After performing all the operations
described in the previous para-
graphs, turn the water tap on com-
pletely, open the appliance door and
press ON-OFF button "
A
": indica-
tor light "
B
" comes on. Your appli-
ance is now on and awaiting instruc-
tions.
Selecting the wash
cycle.
Select the wash cycle by pressing
button "
P
". Each time this button is
pressed, one of the indicator lights
"
M
" will come on in sequence, se-
lect the wash cycle you deem most
suitable for the type of dishes to
wash (take a look at page 17, where
you will find the wash cycle table).
Close the appliance door and after
a few seconds, you will hear a short
beep: the wash cycle has begun.
Modifying a wash cycle in
progress.
But if you have chosen the wrong
cycle, not to worry! You can modify
the wash cycle in progress, if it has
only just started. Open the appli-
ance door carefully to avoid any
hot water splashes, then keep but-
ton "
P
" pressed for approximately
5 seconds, until you hear a short
beep. Indicator light "
M
" will come
off and at this point, all the settings
will have been cancelled. You are
now free to re-set the correct wash
cycle.
You've left out a dish?
Well, it happens to everyone. Inter-
rupt the wash cycle by opening the
appliance door with the utmost
care, as usual, then insert the dish
you had forgotten. When you shut
the appliance door, the cycle will
start up from where you interrupted
it.
Finished?
The end of the wash cycle is indi-
cated by a double beep and the
flashing of the wash cycle indicator
light "
M
".
Turn off the water tap.
Wait a few minutes before unload-
ing the dishes: they are very hot! If
you wait a little while, they dry
better thanks to the steam. Empty
the lower rack first.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity comes
back on or when you close the door.
Everything is under control!
You decide when it
starts.
When you have loaded the dishes,
you can choose when to start your
dishwasher before setting the de-
sired wash cycle. Press button "
C
"
to delay the start of the wash cycle
by 2, 4 or 6 hours. Each time you
press it, you will hear a short beep
and indicator light "
D
" correspond-
ing to the selected delay will come
on.
Now you can select the desired
wash cycle. Close the appliance
door and, after you hear the beep,
the countdown to the delayed start
will begin.
Once this time is up, the indicator
light will stop flashing and the wash
cycle will begin.
You have loaded your dishes and you now have
to set the wash cycle. It takes just one minute
to learn how
Starting the dishwasher
Make sure the
wash cycle has
ended before
removing the
dishes!
If you change your mind and you
wish to set a different delay, just
open the appliance door, press but-
ton "
C
" and repeat the selection.
If, on the other hand, you want to
cancel the delayed start set and
you want the wash cycle to start
immediately, press the button re-
peatedly until indicator light "
D
"
comes off. When you close the ap-
pliance door, the wash cycle starts
up and a short beep sounds.
You want to wash on
one rack only?
Remember to use half
the amount of
detergent.
Your dishwasher also allows you to
wash half a load, to save water and
electricity. Before setting any wash
cycle whatsoever, press button "
Q
"
repeatedly to select whether you
want to run a half cycle on the up-
per or lower rack. Each time you
press it, you will hear a short beep
and indicator light "
R
" correspond-
ing to the selected rack will come
on.
Ready, steady, go!
If opening the
door soon after
the end of the
p r o g r a m m e , o r
during it, stand
away from the
Dishwasher, to
avoid possible
injury from hot
steam.
Warning!
Open the dishwasher door,
turn off by pressing button
A
,
unplug the appliance from the
electricity socket to cut off the
power supply;
the power supply
cable should consequently be
easily accessible.
Do you want extra
drying?
Press button "
E
" before you start
the selected wash cycle.
A prolonged beep will inform you
that you have selected extra drying,
a short beep indicates it has been
disabled.
With extra drying, the wash cycle
will last longer, to provide you with
drier dishes.
