8
ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
If the power
socket to which
the appliance is
connected is not
compatible with
the plug, replace
it with a suitable
plug rather than
using adapters or
multiple plugs as
these could cause
overheating or
burns.
Installation and moving
After having bought or moved your dishwasher to another home, a
correct installation ensures that your dishwasher will operate
smoothly and efficiently.
Hot water connection.
Your dishwasher can be supplied
with hot water from the mains
supply (if you have a central heating
system with radiators) at a tempe-
rature of no more than 60°C.
In this case, the wash cycle time
will be about 15 minutes shorter
and the wash will be slightly less
effective.
The connection must be made to
hot water supply following the
same procedures as those indicated
for the cold water connection.
Anti-flooding protection
Your dishwasher is provided with a
special system which blocks the
water supply in the event of leaks
inside the appliance. It is further
equipped with a water inlet hose
comprising an outer clear hose and
an inner red hose, which can both
withstand extremely high pres-
sures. Should the inner hose break,
the outer hose will consequently
turn red. Safety in the event of
flooding is ensured by the second
clear hose that contains the former.
It is vital that you check the outer
hose regularly: if you see it has
turned bright red, then you know
you have to replace it as soon as
possible. Call for an authorised
technical engineer to come and
replace it.
Drain hose connection.
Fit the drain hose into a drain pipe
with a minimum diameter of 4 cm
or place it over the sink. Avoid
restricting or bending it. Use the
special plastic elbow provided (see
figure) to position it in the best
possible way. The free end of the
hose should be between 40 and 100
cm above the ground and should
not be immersed in water.
Electrical connection.
First of all, check that the mains
voltage and frequency values
correspond to those stated on the
rating plate located on the stainless
steel inner door of the appliance
and that the electrical system to
which the dishwasher is connected
is sized for the maximum current
indicated on said rating plate.
Earth: indispensable
safety.
Only now can you plug the
appliance into a socket provided
with an efficient earth connection
(the system's earthing is a
guarantee of safety provided for by
law, make sure your system has
it).
Choose where you want to install
your dishwasher, you can even
place it so that its sides or back
panel are side by side with furniture
or up against the wall. The
dishwasher is provided with water
supply and drain hoses, which can
be directed towards the left or right
to facilitate appropriate
installation.
Easy to build-in
This dishwasher model can be built-
in under a single worktop easily.
The dishwasher comes with an
assembly kit complete with an
instructions sheet.
Levelling.
Once the appliance is positioned,
adjust the feet by screwing them in
or out depending on how high you
want it and to level it so that it is
horizontal. Make sure that it is not
inclined more than 2 degrees. If the
appliance is level, it will help ensure
its correct operation.
Cold water connection.
Connect the cold water supply
hose to a 3/4 gas threaded
connection, taking care to screw it
tightly onto the tap.
If the water hoses are new or have
been out of use for an extended
period of time, let the water run to
make sure it is clear and free of
impurities before making the
connection. If this precaution is not
taken, the water inlet could get
blocked, causing damage to your
dishwasher.
Your dishwasher has arrived
A
The special
plastic elbow
should be
fastened firmly
onto the wall to
prevent the drain
hose from
moving and
allowing water to
spill outside the
drain.
Power supply wire.
Check the power supply wire on a
regular basis; if it is damaged, we
recommend you have it replaced
by an authorised technical
Assistance service centre.
