Ariston 3700511 User Manual Download Page 54

Page: 54 / 64

Congratulations on your purchase of an electric water heater manufactured by Ariston Thermo Group. The appliance

is designed in compliance with the European quality standards and conforms to declared technical characteristics. The

water heater is easy to use; it demonstrates great consumer properties and durability in operation. We hope that you will

be satisfied with its work.

Please, read this manual carefully to ensure proper installation and operation of the water heater.

1. GENERAL INFORMATION

1.1. Delivery set and purpose

1.1.1.

Water heater

1.1.2.

Safety valve

1.1.3.

Bracket

1.1.4.

Installation and operation manual

1.1.5.

Warranty certificate

1.1.6.

Original packing

The appliance is designed for installation inside the buildings, in the household and utility premises. It is intended for water

heating to a temperature below boiling point, with the option of the hot hot water's supply (not intended for drinking) at

several spots (bathroom, kitchen, and toilet) and further maintenance of the set temperature in the automatic mode.

Water heating time depends on the volume of the water heater and the power of the heating element.

1.2. Main elements

1.2.1. Inner tank

1.2.2. Thermal insulation of polyurethane foam providing minimal heat dispersion

1.2.3. Heating element

1.2.4. Temperature controller which allows you to set the desired temperature of the water heating

1.2.5. Thermostat controlling the temperature of water in the tank

1.2.6. Safety valve which is installed at the inlet of the water heater and serves to prevent the return of water to the water

line and protect the tank from excessive pressure

1.2.7. Magnesium anode rod providing additional protection of the inner tank from corrosion

TECHNICAL CHARACTERISTICS

Product range

SLIM

100

120

150

Weight

(kg)

Enamel

Inox

This appliance is conforming with the international standards:

- Electrical safety standards IEC 60335-1 and IEC 60335-2-21.

- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

The products are compliant according to:

- TP TC 004/2011 «Technical regulations of the Customs Union on safety of low voltage equipment».

- TP TC 020/2011 «Technical regulations of the Customs Union on electro-magnetic compatibility».

2. INSTALLATION

Attention! The installation and set-up of the water heater must be carried out by a qualified technician in con-

formity with the applicable rules and hygiene and sanitary standards in force and with any provisions set forth

in this manual.

2.1. Hot-water boiler bonding against the wall

2.1.1.

Water heater mounting is made on the main wall using brackets and fastening hooks. Fastening hooks (not included in the

supply) with a diameter of at least 12 mm are recommended. Depending on the model, you will need 2 or 4 of the fastening hooks.

2.1.2.

Prepared fastening must support a weight that is three times higher than the weight of the water heater filled with water.

2.1.3.

The appliance should be installed as close as possible to the point of water intake to limit heat (

in Fig. 1).

2.1.4.

Allow for a clearance of at least 50 cm under the appliance and a clearance of 10 cm from the ceiling for maintenance.

2.1.5.

Fastening of hooks to the wall must prevent inadvertent movement of the bracket of the water heater over them. After

installation, be sure to check security of the fastening.

2.1.6.

To prevent the property of the customer and (or) third party from damage caused by failures of hot water supply system,

it is recommended to mount the water heater in the premises provided with waterproof floor and sewer drain. Never put objects

sensitive to water under the water heater.

2.1.7.

During mounting water heater in the unprotected areas, you must install underneath the protective tray with drainage

into the sewer.

Before cleaning, isolate the appliance from the mains by
unplugging it or turning the switch off

Install the appliance on a solid wall that is not subjected to
any vibrations

Make electrical connections using cables with conductors
of suitable section

Make sure all control and protection functions operate correctly
before start the appliance

Electric shock

Excessive noise

Incorrect conductor section results in cables overheating.
It may cause fire.

Shutdown or damage of the appliance due to out-of-service
or unregulated control system operation

Before water heater handling, drain hot water

Descale the components in accordance with the instructions
provided in the applicable document. Air the room.
Work is performed in protective clothing, avoiding mixing
different products. The water heater and surrounding
objects shall be protected against ingress of cleansers

Do not use any insecticides, solvents or aggressive detergents
to clean the appliance

Burns

Injury due to contact of the skin or eyes with acidic substances,
inhalation or swallowing of harmful chemical agents.

Damage to the appliance or surrounding objects due to corrosion
caused by acidic substances

Damage to the plastic and painted parts

GENERAL SAFETY NORMS

Damage to the appliance or any objects underneath it due to the
object falling off following vibrations

Injury from an object falling off the appliance due to its vibrations

Electric shock in case of cable, plug, or socket damage

Electric shock. Burns due to the contact with overheated
components. Injuries due to the contact with sharp edges or
protrusions

Injury from the falling appliance

Damage to the appliance or any objects underneath it due to the
appliance falling off from its place of installation