manualshive.com logo in svg

Arista 7000 Series, Quick Start Manual

Share
Download
Arista 7000 Series Quick Start Manual Download Page 18

 

Figure 7: Bracket Mount Examples for Four-Post Rack Mount 

 displays proper bracket mount

configuration examples. 

Figure 8: Improper Bracket Mount Example for Four-Post Rack Mount 

displays an improper bracket mount configuration examples.

Figure 7: Bracket Mount Examples for Four-Post Rack Mount

Figure 8: Improper Bracket Mount Example for Four-Post Rack Mount

Off-set mount is always an improper bracket mount configuration on switches that have six attachment
pins on each side.

3.2.1

 Extracting the Brackets and the Rails

Figure 9: Bracket-Rail Assembly – Before and After Extraction 

 displays a bracket-rail assembly and

the component pieces (bracket and rail) that are extracted from the assembly. Each assembly must
be separated into its component pieces before mounting the switch into a four-post rack. The two
assemblies supplied with the switch are identical.

Figure 9: Bracket-Rail Assembly – Before and After Extraction

This procedure separates a bracket-rail assembly into its component pieces.

1. Grip the rail with your right hand, as shown in 

Extracting the Bracket Rail Assembly-Left

. Pull the

bracket flange away from the rail flange with your left hand until the bracket clip catches on the rail
(

Extracting the Bracket Rail Assembly-Right

).

14

Summary of Contents for 7000 Series























































Reviews:

No comments

Brands by name

Popular brands

Load more brands