background image

EN - 14

SERVICE PARTS

See your Ariens dealer to purchase service 
parts for your unit.

CHECK DUAL HANDLE 

INTERLOCK

1. Stop engine.
2. Engage attachment clutch and then the 

traction drive clutch. 

3. Release the attachment clutch lever. The 

attachment clutch should stay engaged 
until the traction drive clutch lever is 
released. 

IMPORTANT: 

If dual handle interlock does 

not operate correctly, repair as directed in the 
service guide for your unit.

CHECK FASTENERS

Check for loose hardware.

CHECK CLUTCH CABLE 

ADJUSTMENTS

Auger / impeller must stop within 5 seconds 
when attachment clutch lever is released.
Wheels must stop quickly when traction drive 
clutch lever is released.
If clutches do not engage or disengage 
correctly, see 

Adjust Attachment Clutch & 

Brake

 on page 19 or 

Adjust Traction Drive 

Clutch

 on page 21. Refer to the service guide 

for your unit for more information about clutch 
repairs.

CHECK TIRE PRESSURE

Keep tires inflated to pressure listed on tire 
sidewall.

CHECK ENGINE OIL

NOTICE: 

Engine oil level must be maintained 

at correct level or engine damage may occur. 
Refer to engine manual.

CHANGE ENGINE OIL

Refer to engine manual.

CHECK AUGER GEARCASE OIL

1. Place unit on flat, level surface.
2. Remove oil fill plug and seal washer. See 

Figure 16.

IMPORTANT: 

DO NOT remove gearcase 

cover.

Description

Part No.

Ariens Hi-Temp Grease
• 97 ml (3 oz) cartridges (3)
• 414 ml (14 oz) cartridge (1)

00036800
00036700

Ariens L3 Lube – 237 ml (8 oz) 00068800
Shear Bolt and Nut

52100100

Fuel Stabilizer – 118 ml 
(4 oz)
• Except Canada
• For Canada Only

04730400
04742500

Gearcase Seal Washer

06400920

20 Watt Headlight Bulb

00432600

Spark Plug

20001246

Ariens 5W-30 Engine Oil
• 473 ml (16 oz)
• 946 ml (32 oz)

00091000
00067600

Fuse – 5 Amp (Battery)

05076400

Fuse – 7.5 Amp 
(Handwarmers & Headlight)

04954200

WARNING: 

AVOID INJURY. 

Explosive separation of tire and 
rim parts is possible.
• DO NOT inflate tires above 

the recommended pressure. 

• DO NOT inflate tires with a 

compressor; use a hand 
pump.

• DO NOT stand in front of tire 

assembly when inflating. Use 
a clip-on chuck and extension 
hose long enough to allow you 
to stand to one side.

• DO NOT mount a tire without 

proper equipment and 
experience.

Figure 16

1. Auger Gearcase Cover
2. Oil Fill Plug
3. Seal Washer

1

2

3

Summary of Contents for Professional Sno-Thro Series

































Reviews: