background image

9

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 4)

 

Your tractor is equipped with an operator presence sens-

 ing  switch.  When engine is running, any attempt by the 

op er a tor to leave the seat without first setting the parking 

brake will shut off the engine.
• 

Depress clutch/brake pedal (B) into full “BRAKE” posi-

tion and hold.

• 

Place parking brake lever (C)  in “ENGAGED” position 

and re lease pressure from clutch/brake pedal.  Pedal 

should re main in “BRAKE” position.  Ensure parking 

brake will hold tractor securely.

Fig. 4

Fig. 6

Fig. 5

Fig. 7

TO USE THROTTLE CONTROL (D) (See Fig. 6)

Always operate engine at full speed (fast).
• 

Operating engine at less than full speed (fast) reduces 

the engine's operating efficiency.

•  Full speed (fast) of fers the best mower per for mance.

B

C

The operation of any tractor can  result in foreign objects thrown into the eyes, which can 

result in severe eye dam age.  Always wear safety glass es or eye shields while operating 

your tractor or per form ing any ad just ments or repairs.  We rec om mend standard safety 

glasses or a wide vision safety mask worn over spectacles.

OPERATION

GROUND DRIVE  
•  To stop ground drive, depress brake pedal all the way 

down.

•  Move motion control lever (J) to neutral position.
ENGINE   
•  Move throttle control (D) between half and full speed 

(fast) position.

STOPPING (See Fig. 5)

MOWER BLADES  
• 

To stop mower blades, place attachment clutch control 

in the “DIS EN GAGED” position (

).

CAUTION: Always stop tractor com-

 plete ly, as described above, and set 

parking brake before leav ing the op er a-

 tor's position.

NOTE:

 Failure to move throttle control between half and full 

speed (fast) position, before stopping, may cause engine 

to “backfire”.
•  Turn ignition key (F) to “STOP” position and remove 

key. Always remove key when leaving tractor to prevent 

un au tho rized use.

•  Never use the choke to stop the engine.

IMPORTANT: 

LEAVING THE IGNITION SWITCH IN ANY 

POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY 

TO DISCHARGE AND GO DEAD.

NOTE:

 Under certain conditions when tractor is standing 

idle with the engine running, hot engine exhaust gases 

may cause “browning” of grass. To eliminate this possibility, 

always stop engine when stopping tractor on grass areas.

TO MOVE FORWARD AND BACKWARD 

(See Fig. 7)

The direction and speed of movement is controlled by the 

motion control lever(J). 

• 

Start tractor with motion control le ver in neutral position.

•  Release parking brake.
•  Slowly move motion control lever to desired position. 

J

F

D

( ) 

ATTACHMENT 

CLUTCH LEVER  

“ENGAGED”

(

 

) ATTACHMENT 

CLUTCH LEVER 

“DIS EN GAGED”

Summary of Contents for 936053


































































Reviews: