background image

6

ASSEMBLY

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory 
for shipping purposes.  Correct tire pressure is important 
for best cutting performance.
• 

Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be 
properly leveled.  See “TO LEVEL MOWER HOUSING” in 
the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF BELTS

See the Figures that are shown for replacing motion and 
mower blade drive belts in the Service and Adjustments 
sec tion of this manual.  Verify that the belts are routed cor rect ly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that 
the brake is operating properly.  See “TO CHECK BRAKE” 
in the Service and Adjustments section of this manual.

CHECKLIST

BEFORE YOU OPERATE YOUR NEW  TRAC TOR, WE 
WISH TO ENSURE THAT YOU RECEIVE THE BEST 
PERFORMANCE AND SATISFACTION FROM THIS 
QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

  All assembly instructions have been com plet ed.

  No remaining loose parts in carton.

  Battery is properly prepared and charged. 

  Seat is adjusted comfortably and tightened securely.

  All tires are properly inflated.  (For shipping purposes, 

the tires were overinflated at the factory).

  Ensure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results.  (Tires must be 
properly inflated for leveling).

  Check mower and drive belts.  Ensure they are routed 

properly around pulleys and inside all belt keepers.

  Check wiring.  See that all connections are still secure 

and wires are properly clamped.

  Before driving tractor, ensure free 

wheel control 

is in “transmission engaged” position (see “TO 
TRANS PORT” in the Operation section of this man u al).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY 
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT 
ITEMS:

  Engine oil is at proper level.

  Fuel tank is filled with fresh, clean, regular unleaded 

gasoline.

  Become familiar with all controls, their location and 

function.  Operate them before you start the engine.

  Ensure brake system is in safe operating condition.

 

Ensure Operator Presence System and Reverse 
Operation System (ROS) are working properly (See the 
Operation and Maintenance sections in this manual).

 

It is important to purge the transmission before 
op er at ing your tractor for the first time.  Follow proper 
starting and transmission purging instructions (See “TO 
START EN GINE” and “PURGE TRANSMISSION” in 
the Op er a tion section of this manual).

Summary of Contents for 936051






























































Reviews: