manualshive.com logo in svg

Ariens 932031 - ST524, Owner'S/Operator'S Manual

Share
Download
Ariens 932031 - ST524 Owner'S/Operator'S Manual Download Page 22

18

Ariens

®

 

932 Series Sno-Thro

®

Rev. 8/97

STOP

OL0864

A

DJUSTMENTS

 WARNING

ACCIDENTAL ENGINE START UP

 can

cause death or serious injury. ALWAYS
stop engine, remove key, wait for moving
parts to stop and remove wire from spark
plug before adjusting or servicing.

Discharge Chute Deflector

To adjust, loosen then retighten hardware to desired
deflector drag force.

Discharge Chute

If Chute does not stay in position while operating, tighten
nut on carriage bolt at pivot point to increase tension on
spring (Figure 11).

Smooth and easy rotation of properly lubricated chute
with crank (without binding) is obtained by adjusting
pinion and flat gear teeth so they mesh together.

Adjust, using adjustment slots in pinion bracket which is
secured to chute strap.

The chute bracket and gear strap are also slotted for
vertical adjustment of the discharge chute. Loosen
mounting nut and move discharge chute up or down so
that chute ring is approximately centered between
retainer clip and lower ring. Retighten.

Runners

Runners should be adjusted as conditions require.
Raising or lowering runners controls distance scraper
blade (auger/impeller housing) is held above surface
being cleared.

1. Position unit on a hard, flat, smooth level surface.

2. Adjust runners by inserting a spacer of desired

thickness under center of scraper blade, loosen
hardware, slide runners to flat surface (Figure 12).
Allow 1/8" (3mm) between scraper blade and hard
smooth surface. Allow 1-1/4" (30mm) between
scraper blade and uneven surface(s).

3. Retighten hardware.

NOTE:

 Keep housing level by adjusting runners equally.

Uneven runners make unit difficult to steer and results in
uneven clearing.

Scraper Blade

IMPORTANT:

  Damage to auger/impeller housing will

result if blade wears down too far.

Scraper blade is adjustable to compensate for wear.

To adjust scraper blade:

1. Tip unit back onto handlebar, support housing and

loosen nuts retaining blade. With runners adjusted to
their full up position, reposition scraper blade down,
flush with runners, and tighten lock nuts.

Figure 11

DS0110

1. Carriage Bolt
2. Spring
3. Pinion Bracket
4. Pinion
5. Chute Strap
6. Flat Gear

1

2

3

4

5

6

7

8

9

10

11

7. Gear Strap
8. Mounting Nut
9. Chute Ring

10. Lower ring

11. Retainer Clip

Figure 12

OS0480

1

2

1. Runner
2. Runner Hardware

Summary of Contents for 932031 - ST524






























Reviews:

No comments

Brands by name

Popular brands

Load more brands