manualshive.com logo in svg

Ariens 932031 - ST524, Owner'S/Operator'S Manual

Share
Download
Ariens 932031 - ST524 Owner'S/Operator'S Manual Download Page 11

Rev. 8/97

Ariens

®

 

932 Series Sno-Thro

®

7

Explosive Fuel

Fuel is highly flammable and its vapors
are explosive. Handle with care. Use an
approved fuel container.

NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.

NEVER fill fuel tank when engine is
running or hot from operation.

NEVER fill or drain fuel tank indoors.

Replace fuel cap securely and clean up
spilled fuel.

Replacement Parts

ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler
can cause fire or explosion.

Hardware

Keep hardware tight.

Cleaning

Keep unit free of ice or other debris.
Clean up oil or fuel spills.

Storage

For unit storage or extended storage:

• NEVER store with fuel in fuel tank,

inside a building where any ignition
sources are present

• Allow engine to cool completely

• For extended storage, clean unit

thoroughly. See Engine Manual for
proper storage.

Transport

Use extra care when loading or
unloading unit onto trailer or truck.

Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages
that could be damaged.

DO NOT transport machine while
engine is running.

Close Fuel Shut Off Valve before
transport to prevent fuel leakage.

A

TTACHMENTS

 

AND

A

CCESSORIES

Use only attachments or accessories
designed for your unit.

Check attachment components
frequently. If worn or damaged, replace
with manufacturer’s recommended
parts.

❄

OL1253

OL1253

OL0920

OL1410

OL2770

OL2140

OL1253

OL3610

Summary of Contents for 932031 - ST524






























Reviews:

No comments

Brands by name

Popular brands

Load more brands