User manual whirlpool D-series with Bluetooth
User manual whirlpool D-series with Bluetooth
Turn on/off the display:
The system is "standby" when the whirlpool connected to the power network.
1.
If the system is on "standby" state, the on/off symbol is visible on the dark screen. If touch any of the buttons on the screen will
activate the backlight with 50% strength. Turn on the system by pressing the power supply button on the control panel for three
seconds. The current temperature (°C) will appear on the display. The temperature sensor is located below the overflow.
2.
The timer set to 2 hours, all functions will automatically turn off after the expiry of this time, and the whirlpool will go into the "standby"
mode.
3.
To turn off the system, press the power supply button on the display again.
Heater:
When water level is above the water level sensor, the heater can be activated. Press the constant temperature button to activate the
heater. Once the water temperature is below the set temperature, the pump and heater will activate. If the set temperature reaches,
the heater will stop automatically. When water level is below the water sensor, the heater and pump stops automatically and the
heater symbol will start flash, if water level will go above water level sensor the heater and pump will start automatically again.
You can set the heater temperature between 35-43 °C. The pre-set temperature is 38 °C. Change setting with the parameter up and
down buttons. To stop the heater, press the constant temperature button, the heater symbol will flash and the pump will run for 10
seconds to cool down the heater and then stop
.
If the system shut down with heater on, the pump will continue run for 5 seconds to
cool down heater.
Water pump: (F= 1~9 Force)
The water pump only works when the water is above the temperature sensor. Keep in mind that the whirlpool has two sensors. One
sensor for the water level is behind the acrylic and not directly visible. The temperature sensor is visible in the whirlpool.
Press the water pump button to activate the pump. If the water is not above the water level sensor, the pump button will flash, but
the pump will start automatically when the water go above the water level sensor. The standard operating time of the water pump is
20 minutes. If the water pump and air pump both work but with a different start time, both pumps will automatically turn off after 20
minutes. To stop the water pump, press the water pump button for two seconds. On the display you can see “off”.
To be able to adjust the water force, the water pump has to be working. Press the SET button until you see “F=” on the display.
Press the parameter setting keys to select a force level between 1 and 9. Force 1 is the most soft water pressure, force 9 the most
powerful.
Underwater light: (C= 1~7 Colour)
The underwater light colour is variable and adjustable in strength. Press the light button to turn on the underwater light. The light color
is white (C=1). To change the colour of the underwater light, press for the 2nd time on the light button and the light will show
automatically the 7 different colors C=1 to C=7. To set the desired colour, press for the 3
rd
time on the light button when the desired
colour appears. To turn the light off, press the light button for the 4th time.
To change colour manually, press the Set button and use the parameter setting buttons to switch manually between the available
colours. If you want to switch off the lights, press the light button.
Brightness underwater light: (B= Brightness)
With the light activated, you can change the brightness in three levels of intensity by pressing the brightness button. The light will
appear in the most bright setting B=3 and can be dimmed to B=1 or B=2 by pressing the brightness button or the parameter setting
buttons.
Music function:
Press the Radio/CD function button to activate the radio. 3 dB will blink for about 5 seconds, then the radio frequency will appear in
the display. The system automatically use the last selected frequency when the radio/CD function is pressed. Once the radio is
activated you can adjust the volume using the parameter setting buttons from 0-19 (3db is default).
To search for a new radio channel, press the set button, then use the parameter setting buttons to select channel. If you press the
parameter setting buttons for 2 seconds, the system will automatically search for a channel. Press the memory button to save the
selected channel. On the display CH(=channel) will appear. Press the parameter setting buttons to choose a preset number from
1-10 and press the memory button to save the channel. To choose a preset channel, press the memory button, then press set
button and use parameter setting buttons to choose preset channel.
To select Bluetooth press the Music function twice (if FM is active, if not Bluetooth is first and only function available).
symbol will appear in the top display and flash and bt will show in the display.
Now the system is searchable and you can start search mode on your Bluetooth device to start pairing. When the “Whirlpool” is
detected, connect and use password
1234
to be able to connect once connected the system will make indication sound.
Once connected the system only connects to music channel, so speech will not go through the system. If there is an incoming or
outgoing call during music streaming, the streaming will stop automatically during the call and start automatically after the call done.
To deactivate the Bluetooth function press the Music button.
Page 5 / 9
Page 6 / 9
