background image

User manual whirlpool D-series with Bluetooth 

User manual whirlpool D-series with Bluetooth 

 

 

Technical Parameters:

 

 

Operation Conditions and Characteristics

 

Rated voltage

 

AC220V-240

 

Rated frequency

 

60HZ

 

Rated current

 

11.8A

 

Rated power

 

2600W

 

Insulating resistance

 

20M

 

Waterproof level

 

IPX5

 

Load Parameters

 

Type of Load

 

Rated Load Voltage

 

Rated Load Frequency

 

Rated Load Power

 

 

Water pump

 

AC220V-240

 

60HZ

 

900W

 

 

Heater water pump

 

AC220V-240

 

60HZ

 

1500W

 

 

Air pump

 

AC220V-240

 

60HZ

 

200W

 

 

Lighting

 

   AC12V

 

 

7W

 

 

Speaker

 

 

 

8

/10W

 

 

 
 
 
 
 

 

Test standaard: 

EN 12764: 2004+A1: 2008 

EN 60335-2-60 (Low Voltage Directive 73/23/EEC) 

EN 1111 

 

1. The instructions for appliances connected to the water mains shall state: 

-the maximum inlet water pressure is 0.5mPa (5 bars) 

-the minimum inlet water pressure is 0.1mPa, if this is necessary for the correct operation of the appliance. 

2. Guidance on the testing and resetting of Residual Current Devices. 

 L 

(Brown 

colour) 

 N 

(Blue 

colour) 

 G 

(Yellow-green 

colour) 

3. Maximum hot water temperature: 80°C. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Page 9 / 9 

Foreword:

 

This manual is general for all whirlpools in the BT-series. The user manual describes safety procedures, operating instructions and general 

maintenance. Please take your time to read through this manual before installing and using the product and make the instructions available. 

 

Important note to installer/ customer:

 

Please check the description on the packaging matches the item you have ordered and check the packaging visually on damages upon delivery. 

Let us know directly by e-mail if there is an issue. If the product should be returned, we only accept the product packed in the original and 

undamaged packaging. Please ensure that all items are inspected for fault/damage prior to any installation commencing. Let us know directly by 

e-mail if there is damage. 

 

Safety Instructions:

 

1. 

Do not let children use the whirlpool without supervision of an adult. This appliance is not intended for use by persons (including 

children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 

supervision or adequate instruction concerning use of the appliance by a person responsible for their safety. 

Avoid the possibility that little children can drown. Always have supervision.

 

Avoid the possibility that long hair can be sucked into the water suction. This can lead to injuries.

 

2. 

Since excessive water/moisture temperatures have high potential to cause birth defects in early pregnancy, pregnant limiting water 

temperature to38 °C. Consult your doctor before use. 

3. 

Use of alcohol, drugs or medication before or during use of  the product may lead to unconsciousness and possible drowning or 

increased risk of fatal output of heat stroke. 

4. 

Persons suffering from obesity or with a medical history that includes the use of medication for heart problems, low or high blood 

pressure, problems with blood circulation or diabetes should consult a doctor before using the product. 

5. 

Persons using medication should consult a doctor before using this product, since the use of certain medications can cause 

drowsiness or affect heart rate, blood pressure and blood circulation. 

6. 

Excessive use of this product can lead to heatstroke. Heatstroke occurs when body temperature exceeds normal temperature by 

several degrees. The symptoms include dizziness, drowsiness, unconsciousness and increased body temperature. Heat stroke can 

cause you to (1) distraction the dangers that can occur, (2) can’t feel the heat, (3) do not see the need to stop using the product, (4) 

the lack of physical ability to walk out of the product, (5) foetal damage in pregnant and (6) unconsciousness, that can lead to 

drowning. 

7. 

Protective devices for leakage, overload of power or incorrect voltage must be installed and working. 

8. 

Do not use any other electrical devices, except parts supplied with safety extra-low voltage not exceeding 12V, in or in the direct 

surroundings of the product. 

9. 

If the supply cord is damaged, it must be replaced by a qualified persons in order to avoid a hazard. 

 

 

General: Warning 

!

 

Remove the whirlpool from the package carefully and only with the metal frame. Never lift the whirlpool 

from the parts such as hoses, jets, electra, drain hoses etcetera. 

We advise to install your product in a way that, in case of a service need, you easily can reach the 

specific part without the need to make a lot of costs for removing the casing. 

 
 
 
 
 
 

 

 

Page 2 / 9 

 

Summary of Contents for Whirlpool BT series










Reviews: