After Installation:
41.
Before
supplying
any
power
to
the
product,
you
should
inspect
the
power
cables
to
ensure
the
power
leads
are
properly
connected.
42.
After
installation
and
before
starting
the
product
for
the
first
time,
you
should
inspection
all
the
connections
to
ensure
they
are
properly
connected;
including
parts,
plugs,
hoses,
nuts,
screws,
wires,
etc.
43.
After
you
have
fully
installed
the
unit
and
made
all
the
inspections
to
ensure
the
unit
can
function
safely, fully
clean
the
unit
inside
and
out
to
ensure
the
unit
is
ready
for
usage,
and
also
to
check
for
any
potential
lose
debris
that
may
have
fallen
into
any
of
the
plumbing.
After
a
thorough
visual
inspection,
close
the
drain
and
fill
the
tub
up
to
the
overflow
drain,
submerging
all
the
jets
underwater.
If
any
debris
floats
out,
remove
it.
44.
The
whirlpool
system
will
not
run
unless
the
water-level
sensor
is
fully
submerged
underwater.
The
water-level
sensor
is
placed
above
the
water
line
of
the
water
jets.
45.
Turn-on
the
whirlpool
system
and
operate
it
for
a
minimum
of
10-minutes.
Then
turn-off
the
whirlpool
system
and
without
draining
it,
allow
it
to
sit
for
a
minimum
of
10-minutes.
Now
check
all
the
plumbing,
pipe
works,
hoses,
joints,
threads
and
any
other
connections
for
any
leaks.
If
there
are
any
adjustments
made,
restart
this
test
and
review
all
the
connections
again.
46.
You
must
ensure
the
product
works
as
it
normally
would:
immediately
test
all
functions
of
the
product
to
possibly
find
any
errors.
After
testing,
place
the
tub
against
the
wall(s)
and
seal
the
wall
joints
with
an
acid-free
caulking
agent
and
then
allow
it
to
cure
sufficiently
before
any
further
use.
Additional Precautions:
47.
It
is
not
generally
recommended
to
use
bath
oils
in
whirlpool
bathtubs,
as
the
oil
residue
can
stick
to
the
side
walls
of
the
tub
and
plumbing.
Clean
the
whirlpool
system
after
any
such
uses.
48.
It
is
not
recommended
to
use
coarse
grain
bath
salts
with
the
whirlpool
function,
as
it
may
enter
the
water
pump
and
damage
or
cause
additional
wear
onto
its
internal
components.
6
13
Maintenance:
Recommended cleaning the whirlpool features monthly with a whirlpool clean-
ing solution from your local hardware store. Follow the instructions of the
whirlpool cleaning solution. If not cleaned regularly you may notice black
flakes
in the bath – if this happens you should clean the whirlpool system.
Consider cleaning the whirlpool system with whirlpool cleaning solution re-
peatedly until the black flakes disappear. Soap scum, hair, dead skin, skin
care
products, oil, grease and/or bacteria can contaminate your whirlpool sys-tem, it
is important
to clean regularly.
Consider cleaning the whirlpool system using a cup of chlorine bleach (
sodium
hypochlorite
)
and the minimum amount of warm or hot water to activate the
(water-level sensor) whirlpool system, in between regular cleanings with
whirlpool cleaning solution. Thoroughly flush and rinse the bathtub and
whirlpool system before use. (This is not meant as a substitute for whirlpool
cleaning solution)
The drain can be clogged by hair or soap scum and should be cleaned regu-
larly. Cleaning schedule is based off usage conditions; monitor time frame for
any slowing of drainage, and then set cleaning schedule.
Poor maintenance, infrequent, or irregular cleaning can cause damage to the
faucets or jets. Cleaning schedule is based off usage conditions; generally,
more frequent light cleanings are better than less frequent, heavy cleanings.
When cleaning the chrome parts, do not use cleaning compounds or instru-
ments with abrasives or harsh chemicals. Do not try to remove stains with
hard
objects, such as blades or screwdrivers.
When cleaning the acrylic surfaces of the bathtub, use a soft sponge and a
detergent without ammonia, acetone or other harsh chemicals, to prevent sur-
faces from getting dulled or damaged.
Dulled surfaces can be refinished with an acrylic polishing compound (follow
instructions of polishing compound); first spot test in a non-visible surface
area.
Warning:
The use of cleaning materials other than those recommended by
the
manufacturer can result in damage to the bathtub, whirlpool apparatus, or
other hardware. Spot test in non-visible area.
Warning:
Any service, adjustment or repair is only recommended by an expe-
rienced professional. Only consider a licensed professional for all installation,
servicing or repair work.
