manualshive.com logo in svg

Argus QUICK 100 M, Service Manual, Page: 17 / 22

Share
Download
Argus QUICK 100 M Service Manual Download Page 17

 

 

MAINTENANCE AND FAULT FINDING 

14.147.B_QUICK100M en.SM.V1.00.doc 

ARGUS Medical AG 11.08.04 / PJ 

17 / 22 

7.  MAINTENANCE AND FAULT FINDING 

7.1. Maintenance 

CAUTION! 

Only authorized persons who have been instructed by ARGUS Medical AG or by 
the trained local distributor are allowed to service the QUICK

®

 100 M docking sta-

tion. In case of repair request, send the unit to the local distributor with a report 
outlining the exact nature of the failure. More information is available from: 
 

ARGUS Medical AG 

CH-3627 Heimberg / Switzerland 

E-mail: 

info@argusmedical.com

 

 

CAUTION! 

The safety standard check has to be performed at least every 24 month or after 
10'000 hours of operation. The check has to be done in accordance to the chapter 
11. 
No special maintenance of the QUICK

®

 100 M docking station is necessary. There 

are no wear and tear parts. 
 
Interferences through external high frequency electromagnetic fields (e.g. in com-
bination with surgical equipment) are unknown. In case of doubt we suggest that 
you contact your local distributor. 
 

7.2. Fault code 

The fault code in case of a technical failure is displayed in the history file, refer to 
chapter 5. The possible fault codes registered in the history event log file are listed 
in the table below: 

 

Fault Failure: 
Code: 
21  

ROM 

test 

22  

ROM 

check 

(Runtime) 

23  

RAM 

test/check 

24  

XRAM 

test/check 

25  

CPU 

test 

26   

Invalid state (in PC-Configuration mode) 

27  

Eeprom 

data 

invalid 

32   

5Volt supply out of range 

33   

20Volt supply out of range (delayed 5s) 

44   

Address invalid for config-eeprom 

45   

Address invalid for history-eeprom 

 
Exceptionally a fault code not listed above may appear. In this case we recom-
mend changing the main board. 
 

7.3. Specifications 

Please refer to the user manual for the specifications (cap. 7). 

Summary of Contents for QUICK 100 M























Reviews:

No comments