Argosy HD 360C Manual Download Page 8

 

 

 

Partition The External Hard Disk Drive

 

 

 

Using FDISK Under Windows 98SE/Me 

FDISK is a program to create one or more partitions of the hard disk, after the partition was built and 

formatted, data can be write to the hard disk. 

To partition the external hard disk, you must execute FDISK under the MS-DOS mode under 

Windows 98SE/Me, please follow the steps: 

1. 

Boot-up the computer into Windows 98SE/Me system. Plug the external hard disk to computer, 

and make sure it is recognized. 

2. 

Go into the MS-DOS mode by click on Start 

Ö

 Programs 

Ö

 MS-DOS Prompt. 

3. 

At the DOS prompt, type ‘FDISK’ and press 

Enter

4. 

In the first screen of FDISK, answer the question: Do you want to enable large disk support? 

Y     

if you want to create a partition larger than 2GB (FAT32). 

N     

if you want to create a partition small than 2GB (FAT16). 

5. 

The next screen is ‘FDISK OPTIONS’, 

IMPORTANT: you must type 5 on this screen to change the current fixed disk drive, the 

default fixed drive set by FDISK is your internal hard disk, if you don’t change 

it to the external hard disk, the data of internal hard disk will be destroyed. 

 

Note: If the option 5 doesn’t appear on this screen means the external hard disk is not installed 

properly, please check with the software installation. 

Summary of Contents for HD 360C












Reviews: