background image

Safety and Care Advice

Important -

 Please read these instructions fully before starting assembly

• 

Warning:

 This unit weighs 

approximately 33kgs.

Please lift with care.

• Check you have all the

components and tools listed on 

pages 2 and 3.

• Remove all fittings from the 

plastic bags and separate them 

into their groups.

• Keep children and animals 

away from the work area, small 

parts could choke if swallowed.

• Parts of the assembly will be 

easier with 2 people.

• Make sure you have enough 

space to layout the parts before 

starting.

• Do not stand or put weight on 

the product, this could cause 

damage.

• Assemble the item as close to 

its final position (in the same 

room) as possible.

• Assemble on a soft level 

surface to avoid damaging the 

unit or your floor (use opened  

out unit carton).

1

Care and maintenance

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

• From time to time check that 

there are no loose screws on 

this unit.

• This product should not be 

discarded with household 

waste. Take to your local

authority waste disposal centre.

Note:

 If required the next page 

can be cut out and used as 

reference throughout the 

assembly. Keep this page with 

these instructions for future 

reference.

• We do not

recommend the 

use of power 

drill/drivers 

for 

inserting screws

,

as this could damage the unit.

Only use hand screwdrivers.

• 

Safety note:

 It is

recommended that this unit is 

secured to a wall using the 

overbalance protector kit 

supplied or, an alternative fixing 

method of your choice.

• Dispose of all packaging 

carefully and responsibly.

Summary of Contents for Normandy 411/7717

















Reviews: