Argos Newport Assembly Instructions Manual Download Page 16

Page: 16 / 16

Assembly Instructions

If you need help or have damaged or missing parts, call the

Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR3078

Step

Fit the overbalance

protector

To prevent possible

overbalancing we

recommend that this unit

is secured to a suitable

wall by use of the

overbalance protector kit

. fitted to the unit or, an

alternative fixing method

of your choice.

Wall fixings are not

supplied as they will

need to suit the wall

type.

Note:

Take care when

drilling the wall that you

do not drill into any

pipes, wires etc.

If in doubt, consult an

expert.

Warning:

The

unit is heavy.

Lift with care.

Assembly is complete

Strap

Washer

Wall fixing

(not supplied)

Washer

Screw

(not supplied)

Screw

Summary of Contents for Newport

















Search results

Summary of Contents for Newport

Reviews:

Related manuals for Newport

Brands by name

Popular brands

Argos Newport, Assembly Instructions Manual

Search results

Summary of Contents for Newport

Reviews:

Related manuals for Newport

Brands by name

Popular brands