background image

Components - 

Panels

Please check you have all the panels listed below

Glue Safety -

 Take care when using glue, please follow the advice below

Skin contact:

 Remove contami-

nation by washing with soap and 

water. This procedure should be 

followed prior to aeting and 

drinking.

Eye contact:

 Rinse immediately 

with clean water for 15 minutes 

and seek medical advice.

If swallowed:

 Seek medical 

advice immediately.

2

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

• This product should not be 

discarded with household 

waste. Take to your local 

authority waste disposal centre.

• From time to time check that 

there are no loose screws on 

this unit.

Left Side

 

(D0367A)

(706 x 394mm)

Drawer Divider - D0034A

145 x 249mm

waterfall

1

Top

 

(D0275A)

(1000 x 444mm)

4

Base

 

(D0282A)

(349 x 392mm)

5

Upright

 

(D0368A)

(706 x 394mm)

2

Right Side

 

(D0276A)

(706 x 394mm)

3

80%

If you have damaged or missing components, call the 

Customer Helpline: 08456 400800 

quoting the reference 

numbers below

Shelf

 

(D0285A)

(349 x 373mm)

6

Drawer Base

 

(T161)

(299 x 330mm)

10

Modesty

 

(D0277A)

(602 x 157mm)

7

Drawer Front

 

(D0284A)

(345 x 157mm)

9

Door

 

(D0288A)

(443 x 345mm)

12

Back

 

(X725)

(626 x 373mm)

13

Plinth

 

(D0022A)

(349 x 80mm)

8

Drawer Wrap 

(W161)

(943 x 95mm)

11

Summary of Contents for Caspian 355/9424

















Reviews: