background image

L

Assembly Instructions

12

Step

 

17

Fit the standard doors 

and handles

Note:

 The easiest way to 

attach each door       is 

to fit the top hinge first, 

then align and fit the 

other hinges. 

a:

 

Push the hinge     

onto the front part of the 

hinge plate     .

The recess at the bottom 

of screw B goes into the 

slot in the hinge plate.   

b:

 

Keep the hinge   

FLAT against the hinge 

plate      as you slide it 

across as far as it will go.

Tighten screw A.

c:

 

The hinge      must be 

flat against the hinge 

plate      prior to any

adjustment.

d:

 

The hinge      must 

NOT be AT AN ANGLE 

to the hinge plate      

when assembled.

This would indicate that 

the recess at the bottom 

of screw B had not 

located in the slot in the 

hinge plate and the hinge 

would not be secure.

Remove the hinge from 

the hinge plate and then 

re-assemble being 

careful to follow

instructions a-c.

e:

 

Attach a handle      to  

each standard door       

using 2 screws     .

O

O

O

M

M

M

O

M

L

G

8

8

e:

a:

b:

c:

d:

M

O

M

M

B

M

O

O

O

A

O

M

B

8

8

L

G

G

Note:

  This diagram 

shows the long divider on 

the right side of the unit. 

You may have fitted it to 

the left side.

Summary of Contents for Capella 615/5997





















Reviews: