background image

Important

 

- Please read these instructions fully before starting assembly

Mattress height safety notice

Important

1) Please note the maximum mattress height is indicated on the corner post inside the opening at the

    top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.

3) Maximum thickness of the mattress is 20cm:The top of the mattress shall not come above the line

    marked on the bed.

4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are

    loose.

5) Recommended size of the mattress for the top bunk is 90×190cm.For the lower bed is 135×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) Warning: High beds and the upper bed of bunk beds are not suitable for children under six years

    due to the risk of injury from falls.

8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or

    hung on a bunk bed.

Warning

1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance

    between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2012

1

Safety and Care Advice

!

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Place the product on flat and

steady surface during use.

• Keep these instructions for

future use.

• To ensure an easier assembly,

we strongly advise that all

fittings are only finger tightened

during initial assembly. Only

upon completion of the

assembly should all fixing

points be fully tightened.

• Assemble the item as close

 to its final position (in the same

 room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor.

• Parts of the assembly will be

easier with 2 people.

• Dispose of all packaging

carefully and responsibly.

Care and maintenance

• Safety: To avoid any risk of

suffocation to animals or
children dispose of the plastic

bags immediately.

• Cleaning: As with all surfaces

clean with a damp cloth and

mild detergent, do not use
bleach or abrasive products.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on
this unit.

• This product should not be

discarded with household
waste. Take to your local
authority waste disposal centre.

Summary of Contents for 758/5425











Reviews: