Arctiko SUF 100 Operating Instructions Manual Download Page 5

5

Warning:

Regulations require that this appliance must be earthed

The manufacturer declines all liability for injury to persons or animals and for damage to property resulting 
from failure to observe the above procedures and reminders.

If the socket and plug are not of the same type, please have the plug or socket replaced by a qualified 
electrician. 

Do under no circumstances use extension leads or adaptors.
1.

The freezer should be connected by an authorised electrician or by the company, which sold the 

freezer! Incorrect installation may damage the freezer.

2.  Place the freezer on a flat floor, which can take the weight of the freezer.

3.  The electrical installation should be earthed.

4.  Do not use extension cables, but connect the freezer directly to a fixed installation. 

5.  The freezer should be placed in a dry location, and should not be subjected to water on the cabinet. If 

water gets into the electrical parts it may cause short-circuiting.

6.  In the event of functional or electrical irregularities, please contact an authorised servicing engineer.

Before commissioning

Clean the freezer both inside and out using a damp, wrung out cloth. Dry with a dry cloth.
The smell from the plastic parts in the freezer will disappear once the freezer has been cooled down.

Start procedure

Put the plug in the socket.
The thermostat/thermometer will start to flash. The thermostat was pre-set by the producer. The freezer 
should run for at least 6 hours before the thermostat is changed. (Stabilisation of the cooling system).

The alarm function will not start before the temperature has reached temperature St1 = set point for the first 
time.

Starting up the freezer

Start the freezer. Set the thermostat at the temperature required. It will now take about 4-5 hours before the 
set temperature is reached. The freezer should be cooled down without anything in it.

Disconnecting the appliance

Electrical disconnecting must be possible either by unplugging the appliance or by means of a double pole 
switch located up-line from the socket.

Summary of Contents for SUF 100





















Reviews: