background image

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

23

An accessory Vent Guard Kit is REQUIRED for downflow applications

where the vent exits through the lower portion of the furnace casing. See

Fig. 34

 and Specification  Sheet for accessory listing. Refer to the Vent

Guard Kit Instructions for complete details. 

The horizontal portion of the venting system shall slope upwards not less

than 1/4-in. per linear ft. (21 mm/M) from the furnace to the vent and

shall be rigidly supported every 5 ft. (2 M) or less with metal hangers or

straps to ensure there is no movement after installation. 

SIDEWALL VENTING 

This furnace is not approved for direct sidewall horizontal venting. 
Per section 12.4.3 of the current edition of NFPA54/ANSI Z223.1, any

listed mechanical venter may be used, when approved by the authority

having jurisdiction. 
Select  the  listed  mechanical  venter  to  match  the  Btuh  input  of  the

furnace  being  vented.  Follow  all  manufacturer’s  installation

requirements  for  venting  and  termination  included  with  the  listed

mechanical venter. 

Caution!! For the following applications, use the minimum vertical vent heights as specified below. 

For all other applications, follow exclusively the National Fuel Gas Code.

 

NOTE:

 All vent configurations must also meet National Fuel Gas Code venting requirements NFGC

*4 in. (102 mm) inside casing or vent guard

**Including 4 in. (102 mm) vent section(s)

 

A03210

Fig. 31 – Downflow Application-Vent Elbow Up then Left

 

A03209

Fig. 32 – Upflow Application-Vent Elbow Right

FURNACE

ORIENTATION 

VENT ORIENTATION

FURNACE INPUT

(BTUH/HR) 

MIN. VENT 

DIAMETER

IN. (mm)* 

MIN. VERTICAL VENT HEIGHT

FT. (M)** 

Downflow 

Vent elbow left, then up 

Fig. 34

 

154,000 132,000 110,000

5 (127)

12 (3.6)

Horizontal Left 

Vent elbow right, then up 

Fig. 43

154,000 132,000 

5 (127)

7 (2.1)

Horizontal Left 

Vent Elbow up 

Fig. 41

 

154,000 132,000 

5 (127)

7 (2.1)

Horizontal Left 

Vent elbow right 

Fig. 40

 

154,000 

5 (127)

7 (2.1)

Downflow 

Vent elbow up then left 

Fig. 31

110,000

5 (127) 

10 (3.0)

Downflow 

Vent elbow up, then right 

Fig. 37

110,000

5 (127) 

10 (3.0)

SEE NOTES:1,2,3,4,5,7,8,9
on the page following
these figures

SEE NOTES: 1,2,3,4,7,8,9
on the pages following
these figures

Summary of Contents for A Series









































Reviews: