Arcoaire A Series Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 23 / 40

N80ESN/N80ESL(Series A): Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

An accessory Vent Guard Kit is REQUIRED for downflow applications

where the vent exits through the lower portion of the furnace casing. See

Fig. 34

and Specification Sheet for accessory listing. Refer to the Vent

Guard Kit Instructions for complete details.

The horizontal portion of the venting system shall slope upwards not less

than 1/4-in. per linear ft. (21 mm/M) from the furnace to the vent and

shall be rigidly supported every 5 ft. (2 M) or less with metal hangers or

straps to ensure there is no movement after installation.

SIDEWALL VENTING

This furnace is not approved for direct sidewall horizontal venting.
Per section 12.4.3 of the current edition of NFPA54/ANSI Z223.1, any

listed mechanical venter may be used, when approved by the authority

having jurisdiction.
Select the listed mechanical venter to match the Btuh input of the

furnace being vented. Follow all manufacturer’s installation

requirements for venting and termination included with the listed

mechanical venter.

Caution!! For the following applications, use the minimum vertical vent heights as specified below.

For all other applications, follow exclusively the National Fuel Gas Code.

NOTE:

All vent configurations must also meet National Fuel Gas Code venting requirements NFGC

*4 in. (102 mm) inside casing or vent guard

**Including 4 in. (102 mm) vent section(s)

A03210

Fig. 31 – Downflow Application-Vent Elbow Up then Left

A03209

Fig. 32 – Upflow Application-Vent Elbow Right

FURNACE

ORIENTATION

VENT ORIENTATION

FURNACE INPUT

(BTUH/HR)

MIN. VENT

DIAMETER

IN. (mm)*

MIN. VERTICAL VENT HEIGHT

FT. (M)**

Downflow

Vent elbow left, then up

Fig. 34

154,000 132,000 110,000

5 (127)

12 (3.6)

Horizontal Left

Vent elbow right, then up

Fig. 43

154,000 132,000

5 (127)

7 (2.1)

Horizontal Left

Vent Elbow up

Fig. 41

154,000 132,000

5 (127)

7 (2.1)

Horizontal Left

Vent elbow right

Fig. 40

154,000

5 (127)

7 (2.1)

Downflow

Vent elbow up then left

Fig. 31

110,000

5 (127)

10 (3.0)

Downflow

Vent elbow up, then right

Fig. 37

110,000

5 (127)

10 (3.0)

SEE NOTES:1,2,3,4,5,7,8,9
on the page following
these figures

SEE NOTES: 1,2,3,4,7,8,9
on the pages following
these figures

Summary of Contents for A Series









































Search results

Summary of Contents for A Series

Reviews:

Related manuals for A Series

Brands by name

Popular brands

Arcoaire A Series, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for A Series

Reviews:

Related manuals for A Series

Brands by name

Popular brands