Arcam CD33, Handbook

Page: 6 / 8

6
7
Using the remote control
CR-314
RPT CLEAR
0
PROG
A-B
7
8
9
DISP
4 5 6
CD
DVD
1 2 3
OK
OPEN
MUTE
P
MODE
CD/DVD REMOTE
CD DVD
SUBT
ZOOM AUDIO MEM RTN
ANGLE SETUP STATUS SRCH
MENU TITLE
NOTE
Remember to install the two AAA batteries supplied
before trying to use your remote control.
Do not place anything in front of the FMJ badge on
the top left of the CD player (where the IR receiver
is located), or the remote control may not work.
Note that greyed-out buttons on the remote control
are DVD-specific and are not used with the CD
player.
CD/DVD
Ensure that CD mode is selected using the CD/DVD
toggle button. The ‘CD’ LED above the CD/DVD button is
lit briefly when CD mode is selected.
0–9 KEYPAD
This allows direct access to individual tracks on the
disc. To select a track, press the corresponding keypad
button and then press
. For tracks greater than
9, enter the digits in sequence. For example, to play
track 15, press and hold 1, then press 5.
CLEAR
If you make a mistake whilst programming you can
delete the last entered track by pressing ‘CLEAR’.
To delete all the programmed tracks press ‘CLEAR’
repeatedly until ‘0’ is displayed.
To exit the program facility, press ‘PROG’.
PROG
You can program a selection of up to 24 tracks from
a disc to play in any order. Select a track by using the
and buttons, then press ‘PROG’ to program
the track into memory (‘PROGRAM’ appears
on the display to indicate that you have started
programming a sequence). Repeat these steps to
program the remaining tracks in your selection.
Alternatively, press ‘PROG’ once and enter your track
selection using the 0–9 keypad.
The display shows the track numbers programmed,
the total length of the programmed sequence and
the number of tracks programmed (shown by a
number below the word ‘STEP’).
Each time you enter a track, the number below ‘STEP’
increments by one and flashes until you press ‘PROG’
to confirm. If you fail to press ‘PROG’ within about
five seconds, the display stops flashing and you will
have to reselect the track.
Press ‘
’ to play the program. Press ‘ ’ again to
replay the entire sequence from the start. Press and
hold ‘CLEAR’ to erase the programmed sequence.
Press ‘PROG’ again to exit the program facility: the
display flashes ‘CONTINUE’ and shows ‘0’.
MUTE
Stops sound to the speaker outputs of certain Arcam
amplifiers.
/–
Adjusts the volume on Arcam remote-controllable
amplifiers.
Note that the volume ‘+/–’ controls and ‘MUTE’
button have no effect on the audio output level of
the CD players.
A–B
This button enables you to repeat any section of music
within a track. Whilst the disc is playing, press the ‘A–B’
button at the start of the section you wish to repeat.
‘REPEAT’ is shown on the display and the letter ‘A–’ flashes.
Press the button a second time when you reach the end
of the section you wish to repeat. The ‘A–B’ letters stop
flashing and remain lit. This section will repeat until you
press ‘ ’ or ‘
’ or ‘ ’. The forward search button ( )
moves forward within the selected loop.
RPT
To repeat the entire CD or a pre-programmed selection
of tracks press ‘RPT’ once: ‘REPEAT’ lights on the display. To
repeat a particular track, select that track and then press
‘RPT’ twice so that ‘REPEAT 1’ is shown on the display.
If you now select a different track, that track is repeated
instead.
To cancel the repeat function press ‘RPT’ a third time.
SKIP AND SEARCH TRACK
Skip track backwards and forwards; Search backwards and
forwards.
OPEN
Opens and closes the CD tray
PLAYBACK CONTROL
Pause, Play and Stop
P MODE
Press once to shuffle play CD tracks (i.e. play them in a random
order). Press again to cancel shuffle play.
DISP
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
TITLE
Press ‘
TITLE’
once to display the remaining time of the currently
playing track. Press again to display the time remaining of the
disc. Press a third time to turn the text display on.
Press ‘
TITLE’ again and the display reverts to its original setting,
showing the time elapsed for the current track.
For CDs with text, pressing ‘
TITLE’
once while the disc is loaded
but not playing displays the artist’s name.
Pressing ‘
TITLE’ a second time displays the total number of
tracks and the total playing time.