background image

 

 

 

WEKA_IOM_MWG_EN.docx  /  01.04.2020 

3 / 31 

1. 

Symbols and signs used in the instruction manual 

 

Warning 

Indicates potential damage to the device and / or an injury of the operator or 
user in case of failure to observe the instructions. 

 

Caution 

Indicates potential damage to the device in case of failure to observe the 
instructions. 

 

 

Safety note 

For equipment with normal conditions of use in explosion-prone environments 
according to EU-Directive 2014/34/EU (ATEX) or IECEx scheme. 
These notes apply in addition to all other notes. 

 

2. 

Safety notes and warnings 

The manufacturer is not liable for damages which are caused as a result of failure to observe safety notes 
and warnings. 
 

 

Burn hazard! Work on hot magnetic level indicators can lead to bodily injuries and burns. The 
surfaces of the float chambers and the process connections can become hot. Let the tank cool 
down to ambient temperature prior to carrying out any work on the magnetic level indicator. 
Wear appropriate PPE (gloves, face protection, possibly respiratory protection equipment). 
Keep sufficient distance during operation. 

 

The magnetic level indicator and thus also the transmitter can unnoticeably become 
inoperative by a blocking of the float. Should you be unsure about the liquid level indicated 
another method should be used to check the magnetic level indicator.

 

 

Should you suspect a defective function or should you find such defective function, it must be 
remedied. 

 

 

Only use the magnetic level indicator and the transmitter, once you have read and understood 
the complete instruction manual. 

 

The present instruction manual must also be accessible for later users. 

 

Keep magnetic and magnetisable parts (magnets, construction steel, steel wire or clamps etc.) 
away from the magnetic level indicator or accessories such as the transmitter. This also 
applies to strong electromagnetic fields (transformers, welding equipment etc.), as both can 
interfere with the magnetic force of the magnets contained in the magnetic level indicator or the 
transmitter and can lead to malfunctions or failures of the indicator or the accessory parts 
(switch, transmitter,  measuring converter) attached. 

 

Replace damaged or faulty components with original spare parts. 

 

Solvents can blunt the plastic components used or can cause cracks. Clean the devices with 
soap and water or a plastic cleaner. 

 
 

 

Summary of Contents for WEKA 29710 Series

































Reviews: