background image

 

Page 19

 
 

5.  Program 4-digit Security Code 

 
Prior to rotating the transmitter power key-switch to START position to begin operation, you must first 

enter a 4-digit security code in order to proceed further. When this 4-digit security code is input correctly, 

a green light will appear on the Status LED. Please refer to the instruction below on how to program the 

4-digit security code.

 

 

a. 

Press and hold PB1, PB2, PB3 and PB4 and rotate the power key to START position at the same 

time.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

b. 

A constant orange light will appear on the Status LED telling you that you are in the security code 

programming mode. 

c. 

For newly purchased system with the security code function deactivated (default setting), press 

PB1 four times (1111) to activate the security code function. At this time the Status LED on the 

transmitter will blink orange slowly telling you that the 4 digits entered is correct. Then select your 

own 4-digit security code by pressing PB1, PB2, PB3 or PB4 on the transmitter (four presses 

randomly). At this time a fast orange blinks is displayed on the Status LED telling you to 

reconfirm the 4-digit security code you have just entered. A green light will appear once you have 

re-entered the same 4-digit security code again (programming completed). If red light is shown on 

the Status LED after you have re-entered the security code (incorrect input), then you must reset 

the transmitter power and then repeat step a, b and c again. 

 

Steps:

 Press and hold PB1~PB4 and rotate power key to START position 

 constant orange 

 

press PB1 four times (for new systems) or 4-digit security code 

 slow orange blinks 

 enter the 

new 4-digit security code 

 fast orange blinks 

 re-enter the same 4-didgit security code again 

 green light.       

 

d. 

If you wish to cancel the security code function, then repeat a, b, c above and press PB1 four times 

as your new security code (security code function disabled). 

e. 

If you do not remember the 4-digit security code, then you must contact your dealer or distributor 

for further assistance.

 

 
 
 
 
 

Summary of Contents for FLEX 12EX












































Reviews: