Aradex VECTOPOWER VP5000-DC Installation Manual Download Page 159

Page: 159 / 173

VP5000-DC/DC60, VP5000-DC/DC200-HL

Disassembly and disposal

Last edited 2019-02-08
by Sonja Scheunert

Filename
VP5000_DCDC60_200-HL_installation_manual_v1-4en.docx

159 / 173

Secure the VECTOPOWER against falling or overturning.

CAUTION!

Risk of injury due to high weight

Tilting or dropping the VECTOPOWER

can cause injuries such as crushing or bruising.

•

Only use lifting equipment that is suitable and approved for the weight (e.g., forklifts, lift
trucks) and lifting gear.

•

No persons or body parts may be under the suspended load during lifting, transport, or
disassembly.

•

Wear suitable personal protective equipment such as safety shoes.

Loosen the screws.

Remove the VECTOPOWER.

Results:

•

The VECTOPOWER is removed.

•

Send the VECTOPOWER back to ARADEX AG. ARADEX AG takes care of the disposal.

Disposing of recyclable materials

10.3

Send the VECTOPOWER back to ARADEX AG for scrapping.

Summary of Contents for VECTOPOWER VP5000-DC














































































































































































Search results

Summary of Contents for VECTOPOWER VP5000-DC

Reviews:

Related manuals for VECTOPOWER VP5000-DC

Brands by name

Popular brands

Aradex VECTOPOWER VP5000-DC, Installation Manual

Search results

Summary of Contents for VECTOPOWER VP5000-DC

Reviews:

Related manuals for VECTOPOWER VP5000-DC

Brands by name

Popular brands