background image

11 - Error Check/Service/Warranty 

 

Your retailer is responsible for and the contact 
person for warranty services. This applies in particular 
to promises that exceed the two-year statutory 
warranty. All warranty commitments are therefore listed 
on your retailer's proof of purchase (invoice). 

 

Aquavolta® General Sales and Service Center: 
Aquacentrum, Inh. Yasin Akgün 
Münchener Str. 4 a 
D-85748 Garching near Munich 

www.aquacentrum.de

 

•  Waste Electrical Equipment Register: WEEE Reg. No. DE 

93599565 

•  Aquavolta® is a word mark protected by the German 

Patent and Trademark Office as well as by the EUIPO 

Problem

 

Cause 
testing

 

Solution

 

Booster 

Battery charged? 

Connect power supply unit if 
necessary 

does not work  Foreign body in the  Production containers and 
(no bubble 
development 

Pressure vessel?  Unscrew cover and 

clean separately 

ling) 

 

 

LED does 
not light 

Battery charged? 

Connect power supply unit if 
necessary 

Charging does 
not work 

Check plug and 
cable 

If power supply unit is 
defective. Notify dealer. 

Leakage 

Check the seat and 
condition of the 
seals 

Adjust seals or replace with 
replacement seals if 
necessary. 

 

 

 

 

 

 

 

 

Summary of Contents for H2-TURBO














Reviews: