Flow - Setup Menu - Units of Volume 7.4
Page 68
MULTI-PARAMETER TRANSMITTER USER’S MANUAL
Flow - Setup Menu - Units of Volume 7.4
UP
DOWN
UP
DOWN
DOWN
UP
UP
DOWN
UP
DOWN
DOWN
DOWN
DOWN
UP
DOWN
DOWN
DOWN
UP
DOWN
DOWN
DOWN
DOWN
UNITS OF VOLUME
The user can select from four predefined units of Volume, or create their own custom value. The four predefined units are
US Gallons GP
Cubic Feet CF
Liters LP
Cubic Meters CM
The user can also select any two custom characters to represent units from AA to ZZ and an input multiplier which will
numerically relate the custom unit of measure to US Gallons. The input multiplier can be set at any value between 0.0001
and 10000.
The Units of Measurement is broken into two variables, UNITS OF VOLUME and UNITS OF TIME. The two variables are
then combined to display the desired units of measure. For example, if units of Volume is to set Cubic Meters (CM) and
Units of Time is set for Seconds (S), the controller will display flow as Cubic Meters per Second on the front LED display.
Press the key once which will move the
cursor over the smallest digit of the custom multiplier.
With "N" selected, pressing
the key will NOT
store the selection, but
simply return to the UNITS
OF VOLUME Menu. This
function is useful if you
wish to view the current
selection without making
any changes.
NOTE:
ACCELERATOR KEYS
Pressing the or
key once will change the value
by the smallest digit. Holding the
key down will cause the value to
change at an increasing rate until
the key is released. Pressing the
key again will cause the value to
start changing at it's slowest rate
again. This allows the user to get
to the new multiplier value
quickly.
DOWN
UP
UP
NOTE
PRESS THE AND KEYS
TOGETHER TO GO IMMEDIATELY
BACK TO RUN MODE
DOWN
RUN MODE
To select custom units, press the,
press the key, then the
key, which will move the cursor back
to the right hand digit of the custom
unit character.
Again, use the or
keys to select the appropriate
text character, then press the
key to move the cursor to the RH
position.
Press the key to accept the setting and
move to the custom multiplier setting.
Then press the key to store the
selection and return to the UNITS OF
VOLUME menu.
Or press the key to highlight
Use the or keys to
select the correct multiplier. When
complete, press the key to
move the cursor to the RH position.
Not stored
DOWN
the Y character.
Stored
Use the or
keys to select the
appropriate text
character, then press the
key to move to the
left hand text character
DOWN
UP
DOWN
UP
DOWN
DOWN
Setting the custom
Units of Volume and
Multiplier is now
complete, press the
key to accept
the setting and move
to the store function
DOWN
DOWN
UP
In this example, the units will be
changed to ML (milliliters), and the
multiplier changed to 3785.4 since
one U.S. Gallon equals 3785.4
milliliters.
Press the key to accept the
setting and move to the store function
Press the key once
which will move the cursor
over the last character of the
volume unit setting.
DOWN
To select a specific predefined unit,
press the key once which
will move the cursor back to the RH
side of the display.
Use the or keys to
scroll through the available ranges
UP
DOWN
DOWN
CUSTOM 1.0000 >
UNITS OF VOLUME
UNITS OF VOLUME
CUSTOM ? L >
CUSTOM ? ? >
UNITS OF VOLUME
CUSTOM ? ? >
UNITS OF VOLUME
CUBIC METER C M >
UNITS OF VOLUME
LITERS L P >
UNITS OF VOLUME
CUBIC FEET C F >
US GALLONS G P >
UNITS OF VOLUME
UNITS OF VOLUME
TOTAL 0
CALIBRATION
UTILITIES
SETUP
UNITS OF VOLUME
UNITS OF VOLUME
CUSTOM 3785.4 >
CUSTOM ML >
UNITS OF VOLUME
STORE? Y N
STORE? Y N
CUSTOM 1.000 0 >
CUSTOM 3785. 4 >
UNITS OF VOLUME
UNITS OF VOLUME
UNITS OF VOLUME
UNITS OF VOLUME
CUSTOM ? ? >
UNITS OF VOLUME
CUSTOM M L >
CUSTOM ?? >
UNITS OF VOLUME
UNITS OF VOLUME
CUBIC FEET C F >
UNITS OF VOLUME
US GALLONS GP >
UNITS OF VOLUME
W A R N I N G
Changing the units of Volume
with an accumulated flow total
will reset the flow total to
zero.
Example: If the controller has
been running in GPM mode
and has a totalized flow,
changing from GPM to
another unit will reset the
totalizer to zero.
