INSTALLING YOUR AQUAGUARD
®
BLAZE
Make sure that your Aquaguard
®
Blaze is installed by a trained Eureka
Forbes Service Technician only.
1. Input water must be tested for Total Dissolved Solids (TDS).
2. Install your Aquaguard
®
Blaze in a dry ventilated place. Keep it away
from direct sunlight, heating devices or areas below freezing tempera-
ture. Ensure that the height of unit installed on wall is not too high, to
avoid splash of hot water.
3. Ensure that the input water temperature is in the range of 10˚C-40˚C.
Avoid connection to a hot water tap as it can damage the filters.
4. Make sure that the tap water pressure is not exceeding 3.0 kg/cm
2
.
If the input water pressure is more than 3.0kg/cm
2
, installation of a
PRV** (Pressure Reducing Valve) is mandatory.
5. Flush filter and membrane thoroughly and independently for 3-5 min. to
remove fine particles present in the filter.
6. Make sure that the reject water pipe (Blue colour pipe) is placed lower
than the purifier, to avoid stagnation of high TDS reject water in the pipe.
7. TDS regulator should be adjusted by a trained Eureka Forbes Services
technician only to provide healthy water always, as per customer
requirement. (For RO+UV+MTDS)
Input Water Quality Usage Limitations:
1. If the input water iron content is more than 0.3 mg/litre; use of an iron
remover** is recommended as a pre-treatment.
2. If the input water turbidity is more than 5 NTU or comprises colloidal
particles, use of a special filter** is required as a pre-filter.
3. If the input water TDS is more than 1,000 ppm (mg/L) or input water
hardness is more than 300 ppm (mg/L), use of a Membrane life
enhancer** is recommended.
4. Do not install the water purifier if the TDS is more than that prescribed
in the technical specifications.
**Available at an extra cost.
PURIFICATION PROCESS OF AQUAGUARD
®
BLAZE RO+UV+MTDS
TECHNICAL SPECIFICATIONS*
BLAZE RO+UV+MTDS
Copper has antimicrobial, antioxidant, and
anti-inflammatory properties that help to support
healthy metabolism. It also helps to provide the
body with energy and is much needed for growth
and development. The activated carbon removes
organic components and polishes the water,
giving it a sparkling look, making it pure and
great to taste.
The Multi-Stage Purification Process of Aquaguard
®
Blaze Hot & Ambient.
i-Filter™
Multi-layered Polypropylene
Roving Wound Cartridge
Removes fine suspended particles such as dust,
dirt mud and sand from water.
Chemi-Block
(with built-in
Particle Trap Filter™)
Dust-free Bacteriostatic
Activated Carbon Block
Reduces excess chlorine and organic impurities.
Also adsorbs bad taste and odour from the water.
Mineral
Guard™
*+
Micro Controller-based
Electronic Impulse
Producer
Prevents the deposition of dissolved minerals like
Ca and Mg on the Quartz Tube of UV chamber,
thus, enhancing the availability of minerals in water.
Membrane Life
Enhancer***
Special Anti-scalant
Media
Prevents scaling of dissolved salts on the surface
of the membrane, thereby, enhancing the
membrane life and performance.
Reverse
Osmosis
Membrane
Thin Film Composite
(TFC) Reverse Osmosis
Membrane
Reduces TDS, hardness, pesticides and heavy
metals like arsenic, lead and mercury. Eliminates
micro-organisms like bacteria, viruses, protozoa
and cysts.
UV e-boiling
Germicidal UV Lamp
Active
Copper™
Cartridge
+
^^
Bacteriostatic Taste
Enhancer with Active
Copper™ Technology
UV disinfects the water by eliminating waterborne
disease-causing bacteria, viruses and protozoa,
thereby, making it safe to drink.
MTDS
Regulator
Mechanical System
Adjusts the TDS of purified water to provide
healthy water always.
Aquaguard
®
blaze Hot & Ambient
Model
2
Dimension (W X D X H)
330 mm X 440 mm X 490 mm
Net Weight
13 KG (Approx.)
3
Purification Technology
RO+UV+MTDS Regulator
3.9 litres (Ambient water tank - 3.1 litres & Hot
water tank - 0.8 litre)
4
Tank Capacity
i-Filter™, Chemi-Block, Mineral Guard™,
Reverse Osmosis Cartridge, UV e-boiling,
Active Copper™ Cartridge, MTDS Regulator
5
6
Standard Filtration
supplied
1
1
Power Rating
595 Watts (Heater - 550 Watts)
RO Membrane Rating
75 GDP
1
Iron Content (Max.)
0.3 mg/L
2
Total Dissolved Solids
(TDS) (max.)
Up to 2,000 mg/L
++
5
Total Hardness (max.)
600 mg/L
6
Chlorine Content
(Max.)
0.2 mg/L
3
Input Water Turbidity
(Max.)
5 NTU
4
Input Water Pressure
Range**
Up to 3.0 kg/cm²
1
UV Lamp
11 Watts
3
UV Lamp Life
8,000 burning hours (as per UV lamp manufacturer spec.)
4
Operating Voltage Range
150 VAC to 280 VAC, 50 Hz
5
Power Supply
Internal AC/DC Adaptor 24V DC / 2.5 A, Heater Input -
230V AC, 50 Hz.
2
ELECTRICAL SPECIFICATIONS
RECOMMENDED INPUT WATER PARAMETERS
PRODUCT SPECIFICATION
*Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard laboratory conditions
#
. Actual performance may vary
depending on the input water quality, water pressure and condition of filters. If the pressure is higher than the maximum specified, use of a
pressure reducing valve is mandatory. The above accessories are available with our company at an additional cost.
++
If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer
Performance data sheets are available with Eureka Forbes Technical Documentation Centre.
Warranty void if the product is not installed as per recommendations.
#
Standard Test Conditions:
Feed Water Quality: TDS Max: 1,000 mg/litres with NaCl Pressure: 1.0kg/cm
2
, Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below
0.2 mg/litres, Iron: below 0.3 mg/litres Life: 6,000
#
Litres. Pressure on membrane: 75psi. Product Recovery @ 25%.
#
Actual performance may vary based on the input water conditions - TDS, Hardness, Pressure, Temperature & pH. Standard test Condition
are valid for online water supply installation. In suction mode, the product performance may be lower than the claims.
LED INDICATION CHART FOR
AQUAGUARD
®
BLAZE RO+UV+MTDS
Aquaguard
®
BLAZE Hot & Ambient
NOTE: THIS IS A SCHEMATIC ILLUSTRATION OF THE PRODUCT TO GIVE A VISUAL SCHEME OF WORKING OF PRODUCT.
THIS IS NOT AN ACTUAL ENGINEERING DRAWING OF THE PRODUCT.
e-boiling
HERE'S HOW YOUR AQUAGUARD
®
BLAZE RO+UV+MTDS WORKS
MEMBRANE LIFE ENHANCER
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than
1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost.
Membrane life enhancer is
recommended to be installed
if the TDS is above 1000 ppm or
hardness above 300 ppm
is recommended.
,
