background image

4

RECEIVER READY (Rx-R) ASSEMBLY:

Here are a few great radios to choose from for your receiver 
ready (Rx-R) Revolt.

Tactic TX240  (TACJ0245):

 The TX240 radio system is reliable 

and easy to operate. It’s basic but has all the necessary features 
to operate your Revolt.

Futaba 3PMS (FUTK2021):

 This radio system is very reliable 

and offers more operator options. We really like the timer option 
this radio system offers as well as the multi-model memory.

Futaba 4PL (FUTK1400):

 Along with great reliability, this radio 

system offers the most user options. It’s also a great system if 
you want to add to your AquaCraft boat collection. This system 
offers 40 model memory and 10 character naming; great features 
to grow your boat lineup.

NOTE:

 This step will require working on the boat with the radio 

turned on and power to the motor. To prevent any possible injury, 
temporarily remove the propeller from the boat.

1. 

Mount your receiver in your boat by installing hook and loop 

to the bottom of your receiver. Install the receiver in the position 
shown in the picture.

2. 

Plug the steering servo into channel 1 and the motor 

controller into channel 2.

TURN ON YOUR TRANSMITTER.

Set the Throttle Trim to negative (clockwise if you have a dial) 
25%.

If your radio has end point adjustments, check to see that your 
(EPA) is set to 100% both forward and reverse throttle trigger.

Then plug the batteries into the motor controller. At this time you 
will hear one beep letting you know battery power is working to 
the controller. To arm the system, squeeze the throttle trigger 
fully and hold until you hear one more beep. Release the throttle 
trigger and you will hear three more beeps. Your boat is now 
ready to operate.

Note: You will have to go through this simple arming procedure 
each time to run your boat.

If your boat does not beep after plugging in the batteries, adjust 
your throttle trim lower “a lesser percentage” until you hear the 
boat beep. Then continue the arming process.

2

%

6

)

%

7

Plug in the packs

Squeeze the throttle trigger and hold

Release the trigger

« Beep»

« Beep»

« Beep-Beep -Beep»

Your boat is now ready to operate!

NOTE:

 Before or after the above, IF your boat’s power system emits 

consecutive beeps, your throttle trim will likely need to be reversed.

SS

Summary of Contents for Revolt 30













Reviews: