AquaCraft Reef racer 2 Assembly And Operation Manual Download Page 3

❏ 

2.  Slide  off  the  battery  door  on  the  bottom  of  the

transmitter. Install 8 fresh “AA” batteries into the bottom of the
transmitter in the configuration molded into the battery holder.
Re-install the battery door onto the bottom of the transmitter.

❏ 

3. Turn the transmitter “ON” using the switch on the front.

The red LED light next to the on/off switch should light up. If
the LED begins flashing erratically, turn the transmitter off and
check  to  make  sure  that  the  batteries  are  installed  properly. 

If you see a steadily flashing LED, the batteries are low and
need to be replaced.

BATTERY PACK CHARGING & INSTALLATION SEQUENCE

IMPORTANT! The included charger unit is designed for
use in an automobile’s 12-volt power outlet. 

Do  not  attempt  to  charge  a  battery  pack  while  the
automobile is running.

The charger is equipped with a 70” charging lead. It is
highly recommended that the charger be placed outside
of the vehicle while in use.

NEVER  LEAVE  A  CHARGER  AND  BATTERY  PACK
UNATTENDED WHILE CHARGING.

Use only the battery pack and charger intended for use
with  the  Reef  Racer  2.  In  the  event  that  you  use  a
different battery charger, charge this pack at a maximum
charge rate of 1.2 amps.

Charge  the  battery  pack  only  after  it  has  been 
fully discharged.

❏ 

1.  Plug  the  battery  charger  into  an  automobile’s  12-volt

power outlet as shown.

❏ 

2. Join the battery and charger connectors as shown. Do

not force them together; they are designed to fit together only
one way.

❏ 

3. Set the charger’s timer to 

30 minutes

. The red LED on

the  charger  will  illuminate  to  indicate  that  charging  is  in
progress. It is a good idea to check the battery pack every five
(5) minutes. If at any time the battery pack becomes very hot
during the charging process, immediately unplug the charger
from  the  outlet  and  allow  the  battery  to  cool  completely
before attempting to use. 

❏ 

4.  After  charging  is  completed,  unplug  the  charger  unit

from  the  outlet.  Disconnect  the  battery  and  charger
connectors  by  pushing  the  small  tab  down  while  gently
pulling the connectors apart.

Antenna

Power

Light

On/Off

Throttle

Steering

Trim

Steering

Wheel

3

Summary of Contents for Reef racer 2










Reviews: