background image

USER MANUAL FOR AC-2

6

 POOL FILTER 

8

TROUBLE SHOOTING 

PROBLEM

REASON

SOLUTION

Pump is running 
but filtering   
effect is not good 

Filter bag is removed; 
Filter bag is not placed correctly in 
the drums Filter bag is dirty 
&blocked 

Put back the filter bags, replace 
with clean bags 
Check if filter bag is installed 
correctly 

Pump is working but 
no water circulation 

Air bubbles, pockets in Pump piping

Open inlet valve and fill with 
water 
or start/stop the pump a few 
times to flush out the air 

Filter bag is dirty 

Clean filter bag 

Filter basket is blocked 

Clear out the leaves and garbage
of the filter basket 

Water line is too low 

Fill up the pool to 3/4 skimmer 

Incorrect voltage 

Check the voltage of power 
supply  

Pump is working but   
the water flow is small 

Outlet is blocked 

Take out front part of jet to check 
for debris 

Water is found on the   
bottom of the technical 
house

 

Pump, pipe or union part is leaking 

Tighten the pump union re-seal

the connection pipe 

Water is founded inside the light 

Change a new light 

Transformer no work 

Check if the outlet of transformer
is 12V 

Underwater light 
not working 

Wrong wire connection 

Check if the main power is 
closed 

Turn no the device but it 
can not work 

Outside set filtration time T1,T2,T3 

Switch to manual mode check if 
the device can work 

Summary of Contents for AC-26










Reviews: