background image

6  

AS Control Plus         02-2019 EN

By pressing the MODE key you enter the menu. 

The additional functions are indicated in the menu with the 

 

Symbol.

MENU LANGUAGE:

 (factory setting is German

Press the OK key and you can then select by means of the arrow key 
between German, French, Italian, English and Spanish.. 

FILTER PUMP MENU

OVERLOAD PROTECTION: (factory setting is OFF)  

Press the OK key and you are then in the overload protection menu 

where you can first select if the overload protection is to be switched  

on or off. If the OP is switched on, by pressing the OK key the motor  

current will be measured, displayed and saved for the connected pump.  

If you decide to connect a different pump to the 

AS Control Plus

, you  

will need to determine the current for the new pump. You can exit the 

display of the current by pressing the MODE key. Once you have deter-

mined the current, you can select the tolerance level to determine the 

percentage overload at which the overload protection is triggered and  

the filter pump switches off (typically the tolerance is set to 15 %).  

If the contact of the flow switch opens, the pump stops after a delay of 

20 seconds.

FILTER TIMES (Factory settings: 08.00 to 09.00)

By pressing the OK key you can select up to five filter times per day, when the water will 

be channelled via the overflow. This is necessary since the water level is only controlled in 

the collection tank and not in the pool.

CAUTION:

 You must circulate the water via the overflow for at least 30 to 60 minutes per 

day. Only in this way can you measure and control the water level (the measurement 

takes place in the overflow tank).

Additionally, the correct water flow (via the overflow channel) will be re-established by 

entering the times for the overflow operation, which will ensure proper circulation within 

the pool. With public pools, we recommend switching to over-flow operation between  

one and two hours before the pool is occupied in order to ensure the correct water flow.

CAUTION (Warranty exclusion)

Damage which is caused by too low a water level (e.g. burnt-out solar cover) will not be 

covered by us.

CANCELING FILTER TIMES: by pressing the OK key, all filter times can be cancelled. 

During this process you will be asked to confirm whether you really mean to cancel all  

filter times. You confirm by pressing the OK key.

HEATING MENU:

SET VALUE: (factory setting 25 °C)
By pressing the OK key the set point of the water temperature can be 

selected by means of the arrow keys between 1 °C and 40 °C. 

Shortcut: Press the Filter button for 4 seconds to start a backwash

FROST PROTECTION: (factory setting OFF)

By pressing the OK key the frost protection can be selected as ON or OFF by means of 

the arrow keys. In the ON position you can select by means of the OK key at which tem-

perature (-50 °C to +20 °C) the frost protection switches on the filter pump. The adjustable 

hysteresis (temperature difference between ON and OFF) gives the switch-off signal. 

Additionally a collective alarm can be interconnected. If you have a heating system connec- 

ted you can select at which pool water temperature the heating should switch on and off.

Summary of Contents for AS Control Plus





















Reviews: