Aqua One Inspire 40 Assembly Instructions Manual Download Page 2

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs 

approximately 11kgs.

Please lift with care.

• Check you have all the

components and tools listed.

• Remove all fittings from the 

plastic bags and separate them 

into their groups.

• Keep children and animals 

away from the work area, small 

parts could choke if swallowed.

• Parts of the assembly will be 

easier with 2 people.

• Make sure you have enough 

space to layout the parts before 

starting.

• Assemble the item as close to 

its final position (in the same 

room) as possible.

• Assemble on a soft level 

surface to avoid damaging the 

unit or your floor (use opened  

out unit carton).

• We do not

recommend the 

use of power 

drill/drivers for 

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: If there is any 

chance of this unit being pulled 

over by children etc. it is

recommended that the unit is 

secured to a wall using suitable 

fixings (not supplied).

• Dispose of all packaging 

carefully and responsibly.

Care and maintenance

Contact Us

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

Aqua Pacific UK Ltd.

Unit 10, Oriana Way

Nursling Industrial Estate

Southampton

SO16 0YU

Tel +44 (0) 2380 734000

Fax +44 (0) 2380 740200

[email protected]

• From time to time check that 

there are no loose screws on 

this unit.

• This product should not be 

discarded with household 

waste. Take to your local

authority waste disposal centre.

Summary of Contents for Inspire 40










Reviews: