background image

RANGER-AT

TM

LIFT

PART #: F-409RPL-AT1 (WITH ANCHOR)

PART #: F-411RPL-AT1 (WITHOUT ANCHOR)

US PATENT NUMBERS: [7,249,386 B2] [D507,769 S]

350 LB. [159 kg] MAXIMUM CAPACITY

MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER

9889 GARRYMORE LANE

MISSOULA, MT 59808

1-888-687-3552

FAX: 406-549-2602

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1.

READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT
IS INSTALLED AND OPERATED PROPERLY – AS PER THESE INSTRUCTIONS.

2.

WARNING- TO REDUCE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS
PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.

3.

WARNING- DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT.

4.

WARNING- NEVER APPLY DIRECT WATER PRESSURE TO ELECTRONIC COMPONENTS.

5.

DO NOT USE THE RANGER-AT LIFT FOR WATER-DRAFTS OVER 12” (DECK TO WATERLINE).

6.

NEVER OPERATE THIS LIFT UNDER LOAD WITH NO WATER (DRY POOL).

7.

WARNING – FOR SAFETY REASONS NEVER SWIM ALONE.

8.

SAVE A COPY OF THESE INSTRUCTIONS.

AQUA CREEK, LLC 2013

JAN 2013

- READ CAREFULLY-

Check entire box and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the figures and parts listed in this document. It is critical that all
parts be carefully inspected by the installer prior to installation to ensure that no damage occurred in
transit and that a damaged part is not used. If any damage occurred in transit, Aqua Creek Products,
LLC must be notified within three days of receipt of unit. Proper installation cannot be overstressed, as
an improper installation voids Aqua Creek’s warranty and may affect the safety of the user.

Summary of Contents for RANGER-AT F-409RPL-AT1

























Reviews: