background image

11

BATTERY MAINTENANCE

1.

RECHARGE THE BATTERY AS OFTEN AS POSSIBLE

. The battery power unit is

a sealed lead acid battery pack. Frequent recharges will prolong the battery life and
maintain a high cold amperage capacity. THE BATTERY CAN BE STORED ON THE
CHARGER WHEN NOT IN USE.

2. Do NOT expose the battery to freezing temperatures.
3. Do NOT expose the battery to prolonged periods of extreme heat or severe cold

temperatures.

4. Do NOT expose the battery to long periods of direct sunlight. Heat will shorten your

battery life. Optimum operating temperature is below 20 degrees Celsius (68 degrees F.)

5. Never drop or bump the battery pack. This may result in loose or damaged internal

connections, and may bend the battery terminals.

6. Keep battery terminals clean and free from dirt and corrosion to ensure good contact. The

terminals may be cleaned using Scotch Brite or any similar product. Clean off any
corrosion or discoloration on the very top surfaces of the battery contacts and then apply
dielectric grease (supplied with lift) as shown in the figure below.

USING THE “EMERGENCY BUTTON”

on the Pro Pool Lift Control Box

On the front side of the control box is a small recessed
button marked “emergency”. Take a pen or pencil or other
pointed object and depress the “emergency” button. This
will bypass the remote control and send a signal directly to
the actuator to raise the seat out of the pool and back to the
deck or up position.

NOTE: This function will only work if there is sufficient
power in the battery, the battery is properly attached to
the control box, and the control box must be operating
properly.

Summary of Contents for RANGER-AT F-409RPL-AT1

























Reviews: