background image

 

 

 
 

 
 
 

 

 
 
 
 

PRO POOL-AT EXTENDED BASE LIFT

 

PART #: F-004PLB-23-AT1 (& -26-AT1) 

US PATENT NUMBERS: [7,249,386 B2] [D507,769 S] 

450 LB. [204 kg] MAXIMUM CAPACITY

 

MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER 

 
 
 
 
 
 
 

 

        
         9889 GARRYMORE LANE 
             MISSOULA, MT 59808 
                    1-888-687-3552 
                FAX: 406-549-2602 

 

WARNING 

IMPORTANT SAFETY INSTRUCTIONS 

1.

 

READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT 
IS INSTALLED AND OPERATED PROPERLY – AS PER THESE INSTRUCTIONS. 

2.

 

WARNING- TO REDUCE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS 
PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. 

3.

 

WARNING- DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT. 

4.

 

WARNING- NEVER APPLY DIRECT WATER PRESSURE TO ELECTRONIC COMPONENTS. 

5.

 

DO NOT USE THE PRO POOL LIFT FOR WATER-DRAFTS OVER 12” (DECK TO WATERLINE). 

6.

 

NEVER OPERATE THIS LIFT UNDER LOAD WITH NO WATER (DRY POOL). 

7.

 

WARNING – FOR SAFETY REASONS NEVER SWIM ALONE. 

8.

 

SAVE A COPY OF THESE INSTRUCTIONS. 

AQUA CREEK, LLC 2016 

   

       

 

 

 

 

             8/30/16

 

- READ CAREFULLY- 

Check entire box and inside all packing materials for parts.  Before beginning assembly, read the 
instructions and identify parts using the figures and parts listed in this document.  It is critical that all 
parts be carefully inspected by the installer prior to installation to ensure that no damage occurred in 
transit and that a damaged part is not used.  If any damage occurred in transit, Aqua Creek Products, 
LLC must be notified within three days of receipt of unit.  Proper installation cannot be overstressed, as 
an improper installation voids Aqua Creek’s warranty and may affect the safety of the user. 

Summary of Contents for F-004PLB-23-AT1

























Reviews: