AQS Inverboost Premium 10kW User And Service Manual Download Page 29 | Manualshive

Page: 29 / 49

background image

25

Remarks:

1. In heating mode, if the water out temperature is higher than the set temperature over 7

℃

, LED controller

displays EE04 for water over-heating protection.

2. In cooling mode, if the water out temperature is lower than the set temperature over 7

℃

, LED controller

displays PP11 for water over-cooling protection.

EE04 Water Overheating Protection

PP11 Water Overcooling Protection

For example as below:

Mode

Output water

temperature

Set point

temperature

Condition

Malfunction

Heating

mode

36

℃

29

℃

Tout -Tset

≧

7

℃

EE04 Overheating protection

for water temperature (d2-

TH5)

Cooling

mode

23

℃

30

℃

Tset -Tout

≧

7

℃

PP11 Too low protection for

water temperature (d2- TH5)

«
...
27
28
29
30
31
...
»

Summary of Contents for Inverboost Premium 10kW


















































Reviews:

No comments

Related manuals for Inverboost Premium 10kW

ACQUITY UPLC I-Class IVD

Brand: Waters Pages: 98

Brand: Wacker Neuson Pages: 44

Brand: Danfoss Pages: 20

UNI_SAUNA_B4.5KW

Brand: UNIPRODO Pages: 17

Brand: Homa Pages: 11

Brand: O'Clair Pages: 138

Brand: OEG Pages: 28

Brand: Xylem Pages: 20

Brand: Honda Pages: 75

Brand: EOS Pages: 51

Brand: RADtec Pages: 8

Brand: ubbink Pages: 40

Geopump I Series

Brand: Geotech Pages: 16

Brand: Textron Pages: 20

Brand: Sovelor Pages: 16

Idex Godiva GP10/10

Brand: HALE Pages: 28

Brand: Nakayama Pages: 50

Brand: Living & Co Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands