APV SPX DELTA DKR2 Instruction Manual Download Page 40

Page: 40 / 40

SPX FLOW

Design Center

Production

Gottlieb-Daimler-Straße 13

Stefana Rolbieskiego 2

D-59439 Holzwickede, Germany

PL- Bydgoszcz 85-862, Poland

P: (+49) (0) 2301-9186-0

P: (+48) 52 566 76 00

F: (+49) (0) 2301-9186-300

F: (+48) 52 525 99 09

SPX FLOW reserves the right to incorporate the latest design and material changes without notice or obligation.

Design features, materials of construction and dimensional data, as described in this manual, are provided for your information only

and

should not be relied upon unless confirmed in writing. Please contact your local sales representative for product availability in your region.

For more information visit www.spxflow.com.

ISSUED 03/2019 - Translation of original manual
COPYRIGHT ©2019 SPX FLOW, Inc.

APV DELTA DKR2

DOUBLE SEAT BALL VALVE
WITH CLEANING CONNECTION

Scan for DKR2 Valve

Maintenance Video

Summary of Contents for SPX DELTA DKR2









































Search results

Summary of Contents for SPX DELTA DKR2

Reviews:

Related manuals for SPX DELTA DKR2

Brands by name

Popular brands

APV SPX DELTA DKR2, Instruction Manual

Search results

Summary of Contents for SPX DELTA DKR2

Reviews:

Related manuals for SPX DELTA DKR2

Brands by name

Popular brands