APV SPX DELTA DKR2 Instruction Manual Download Page 10

Page: 10 / 40

APV_DKR2_DE-9_032019.indd

Double Seat Ball Valve

DELTA DKR 2

Instruction Manual: UK - rev. 9

APV

5. Auxiliary Equipment

5.1.

Valve position indication

Switches to signal the limit position of the valve ball can be installed

in the yoke area if requested.

We recommend using APV standard proximity switches.

Type: three-wire proximity switch (ref.-No. 08-60-011/93; H16223)

Operating distance: 5 mm / diameter : 11 mm / length: 30 mm

Feedback complete with support and proximity switch

(ref.-No. 15-33-023/33; H32725) for a limit position.

If the customer decides to use valve position indicators other than

those listed above, SPX FLOW cannot assume any liability for the

functionality of the valve.

5.2.

Control unit (CU, fig. 5.2.)

Units with feedback switches and solenoid valves for the pneumatic

control of the valve to be assembled on the actuator are also

available in fieldbus technology.

The assembly of the control unit on the prepared variant of the

turning actuator is possible.

For the startup as well as assembly and disassembly of the different

designs, the corresponding operating manuals must be observed.

The following different designs are available:

CU4 Direct Connect

ref.-No.; ID-No.

CU41 - T Direct Connect

08-45-101/93; H320461

CU4 AS-interface 62 Slaves

ref.-No.; ID-No.

CU41 - T - AS-i extended

08-45-111/93; H320468

CU4 AS-interface 31 Slaves

ref.-No.; ID-No.

CU41 - T - AS-i standard

08-45-251/93; H324674

CU3 Profibus

ref.-No.; ID-No.

CU31 Profibus

08-45-001/93; H315495

CU3 DeviceNet

ref.-No.; ID-No.

CU31 DeviceNet

16-31-240/93; H209422

- For the assembly of a control unit on the DKR2 valve, an adapter is

required.

CU4

control unit

CU3

control unit

fig. 5.2.

adapter

DN 25 - 65; 1“ - 2,5“

designation

ref.-No.; ID-No.

CU4-T-adapter

08-48-601/93; H320475

DN 80 - 125; 3“ - 4“

designation

ref.-No.; ID-No.

CU4-Tmax-adapter

08-48-611/93; H321987

DN 25 - 65; 1“ - 2,5“

designation

ref.-No.; ID-No.

CU2 - adapter K080

08-48-416/93; H209431

DN 80 - 125; 3“ - 4“

designation

ref.-No.; ID-No.

CU2 - adapter DKR80-100

08-48-417/93; H209432

Summary of Contents for SPX DELTA DKR2









































Search results

Summary of Contents for SPX DELTA DKR2

Reviews:

Related manuals for SPX DELTA DKR2

Brands by name

Popular brands

APV SPX DELTA DKR2, Instruction Manual

Search results

Summary of Contents for SPX DELTA DKR2

Reviews:

Related manuals for SPX DELTA DKR2

Brands by name

Popular brands