background image

 

 

13 

9

 

INFORMATION ON NATURE CONSERVATION AND 
ENVIRONMENTAL PROTECTION  

Reduction of noise pollution during use 

Any loose parts should be attached to prevent unnecessary noise.  

Recyclable raw materials during disposal 

Many parts of the implement are made of steel or spring steel (such as the centre frame, roller ring, ...) 
and can be accepted and recycled by a waste disposal plant.  

10

 

TECHNICAL DATA 

Type designation: 

GW 250 M1 

GW 300 M1 

Mode of operation: 

Mode of action: Fine crumbling of clods, reconsolidation and 

pressing down of the seed 

Working width: 

2.40 m 

2.96 m 

Transport width: 

2.44 m 

3 m 

Dimensions (with seeder) 
(H x W x D): 

1.71 m x 2.44 m x 0.95 m 

1.71 m x 3.00 m x 0.95 m 

Dimensions (without seeder) 
(H x W x D): 

1.10 m x 2.44 m x 0.80 m 

1.10 m x 3.00 m x 0.80 m 

Mounting/hitch (three-

point, …): 

linkage 

Weight (full): 

900 kg 

1060 kg 

Roller (410): 

756 kg 

910 kg 

Roller (530): 

640 kg 

792 kg 

Roller (390): 

478 kg 

564 kg 

Ground adaptation: 

Minimal adaptation thanks to flexible roller rings 

Roller types: 

Cambridge roller d = 530 mm 
Cambridge roller d = 390 mm 

Toothed ring roller d = 410 mm 

Minimum tractor performance: 

40 PS 

50 PS 

The performance requirement strongly depends on the lifting 

power of the tractor. 

Combination options: 

Meadow Harrow WS250/300 

Pneumatic seeder PS 120-300 & Multi-Metering System MD with 

electric and hydraulic fan 

11

 

ROAD TRANSPORT  

11.1

 

TRANSPORT ON PUBLIC ROADS (GENERAL INFORMATION) 

  Make sure than none of the safety splints or similar were lost during operation. 

  Comply with the road traffic regulations of your country's legislation. 

  Only relieve the hydraulic hoses at home by putting the tractor control unit into float position. 

  The  holder  for  the  warning  sign  with  lighting  (optional  equipment)  is  mounted  on  the  carrier  for 

the roller and should be positioned vertically to the road. 

  If you are using a ground wheel for the pneumatic spreader with a side bracket, please remove it 

and hang it on the frame so that the transport width of 3 m is maintained. 

Summary of Contents for GW 250 M1

























Reviews: