background image

Thank You!

Thank you for purchasing Aputure® Nova series products. Nova P600c is a high-power  

RGBWW light . The high-power output easily meets the illumination requirements of 

the studio. The high CRI can perfectly restore the skin color of the characters. The high

-quality structure does not fear the heavy work of the studio. It supports multiple 

control protocols. 

IMPORTANT SAFETY INSTRUCTIONS

When using this unit, basic safety precautions should always be 

followed, including the following:

Read and understand all instructions before using.
Close supervision is necessary when any fixture is used by or near children. Do 
not leave the fixture unattended while in use.
Care must be taken as burns can occur from touching hot surfaces.
Do not operate the fixture if a cord is damaged, or if the fixture has been 
dropped or damaged, until it has been examined by qualified service personnel.
Position any power cables such that they will not be tripped over, pulled, or put 
into contact with hot surfaces.
If an extension cord is necessary, a cord with an amperage rating at least equal 
to that of the fixture should be used. Cords rated for less amperage than the 
fixture may overheat.
Always unplug the lighting fixture from the electrical outlet before cleaning and 
servicing, or when not in use. Never yank the cord to remove the plug from the 
outlet.
Let the lighting fixture cool completely before storing. Unplug the power cable 
from lighting fixture before storing and store the cable at assigned space of the 
carrying case.
To reduce the risk of electric shock, do not immerse this fixture in water or any 
other liquids.
To reduce the risk of fire or electric shock, do not disassemble this fixture. 
Contact [email protected] or take the lighting fixture to qualified service 
personnel when service or repair is required. Incorrect reassembly may cause 
electric shock when the lighting fixture is in use.
The use of any accessory attachment not recommended by the manufacturer 
may increase the risk of fire, electric shock, or injury to any persons operating 
the fixture.
Please power this fixture by connecting it to a grounded outlet.
Please do not place the LED lighting fixture near any flammable object.
Only use a dry microfiber cloth to clean the product.
Please do not use the light fixture in wet condition on account of electric shock 
may be caused. 

  1.
  2.
  
  3.
  4.
  
  5.
  
  6.
  
  
  7.
  
  
  8.
  
  
  9.

10.

11.

12.
13.
14.
15.

- 1 -

Nova P600c brings efficient and convenient lighting operation experience to professional 

film and television producers, and helps film and television producers to freely capture the 

vivid details of the shooting scene.

Summary of Contents for Nova P600c

























Reviews: