background image

YC600 Installation/User Manual

4

1.Important Safety Instructions

1.3 Symbols replace words on the equipment, on a display, or in

manuals

Trademark.

Caution, risk of electric shock.

Caution, hot surface.

Symbol for the marking of electrical and electronics devices according to Directive
2002/96/EC. Indicates that the device, accessories and the packaging must not be
disposed as unsorted municipal waste and must be collected separately at the end of
the usage. Please follow Local Ordinances or Regulations for disposal or contact an
authorized representative of the manufacturer for information concerning the
decommissioning of equipment.

CE mark is attached to the solar inverter to verify that the unit follows the
provisions of the European Low Voltage and EMC Directives.

Refer to the operating instructions.

Qualified

personnel

Person adequately advised or supervised by an electrically skilled person to enable
him or her to perceive risks and to avoid hazards which electricity can create. For
the purpose of the safety information of this manual, a "qualified person" is
someone who is familiar with requirements for safety, electrical system and EMC
and is authorized to energize, ground, and tag equipment, systems, and circuits in
accordance with established safety procedures. The inverter and complete system
may only be commissioned and operated by qualified personnel.

Summary of Contents for YC600

























Reviews: