APRILIA RS4 125 Service Station Manual Download

Page: 190 / 298

•

Temporarily install the cylinder on the

piston, without the gasket of the cylin-

der's base.

•

Fit a dial gauge on the specific tool.

•

Take the piston to TDC.

•

Position the dial gauge on one side of

the cylinder and fasten it in order to de-

tect the zero position correctly.

Specific tooling

AP8140266

Dial gauge mounting

•

Move the dial gauge diagonally and

measure the piston protrusion in rela-

tion to the reference surface.

•

Calculate the necessary thickness of

the gasket, selecting it based on the

values shown in the table below.

Installing the cylinder

•

Fit a new cylinder base gasket of the

chosen thickness.

•

Refit the cylinder as indicated in the

figure using the specific clamp tighten-

er tool.

NOTE

BEFORE FITTING THE CYLINDER, CAREFULLY BLOW
AIR INTO THE LUBRICATION DUCT AND LUBRICATE THE
CYLINDER LINER.

Specific tooling

020287Y

tool for sealing ring fitting

Engine

RS4 125

ENG - 190

Summary of Contents for RS4 125











































































































































































































































































































Search results

Summary of Contents for RS4 125

Reviews:

Related manuals for RS4 125

Brands by name

Popular brands

APRILIA RS4 125, Service Station Manual

Search results

Summary of Contents for RS4 125

Reviews:

Related manuals for RS4 125

Brands by name

Popular brands