background image

Model 4200, 4300 & 4400 Media Air Cleaners

Installation Instructions

1.  High voltage may cause serious 

injury from electrical shock. 

Disconnect power to the  

furnace/air handler before 

starting installation.

2.  Sharp edges may cause injury 

from cuts. Use care when cutting 

and handling sheet metal.

 WARNING

1.  To prevent component failure, do not install the air cleaner on the warm 

air supply or in an area where the temperature may exceed 140°F. This 

may include areas above heat exchangers in downflow furnaces or above 

exhaust flues in lowboy furnace cold air returns.

2.  Installation must be done by a qualified heating and air conditioning 

professional. Read instructions thoroughly before beginning installation.

3.  Do not install air cleaner downstream of a UV light. UV lamps will cause 

degradation of the filtering media.

 CAUTION

SPECIFICATIONS

TABLE 1 – Initial Airflow Resistance (inches w.c.) 

Model

Airflow (CFM)

800

1000

1200

1400

1600

1800

2000

4200

.09

.12

.16

.20

.25

.30

.35

4300

.13

.18

.24

.30

.37

NA

NA

4400

.09

.13

.17

.22

.26

.31

.37

Electrical:

 

   Voltage: 18-30 VAC 
   Max Current: 2A (maximum low-voltage current for fan control)

MERV (Minimum Efficiency Reporting Value) @ 347 fpm:

 13

Airflow Capacity:

 see 

Table 1

Replacement Media:

  4200: Model 213 with SelfSeal

 

4300: Model 313 with SelfSeal

™ 

4400: Model 413 with SelfSeal

Max. Equipment Weight:  

   

Cabinet will support 400 lb. static load

Air Cleaner and LED Base Operating Environment: 

 

   Temperature: 0°F – 140°F 
   Humidity: 0-90% non-condensing

Air Cleaner Control Operating Environment: 

 

   Temperature: 20°F – 120°F 
   Humidity: 0-90% non-condensing

Do not wire to EAC terminals of HVAC system. These terminals 

are 120 Volts and will damage the Air Cleaner Control.

 CAUTION

DIMENSIONS

TABLE 2 – Dimensions (inches)

Model

A

B

C

D

E

F

G

H

J

K

4200

19-3/4

25-3/8

21-3/16

6-3/4

27-3/8

21-3/16

19-3/4

22-1/16

25-3/16

23-5/8

4300

18-1/16

20-1/16

15-7/8

6-3/4

22-1/16

15-7/8

18-1/16

20-3/8

23-1/2

21-15/16

4400

15-7/16

28-1/16

23-7/8

6-3/4

30-1/16

23-7/8

15-7/16

17-3/4

20-7/8

19-5/16

A

B

without DOOR

C

D

with Door

F

G H

J K

90-1333

Summary of Contents for 4200









Reviews: