APR APR-2000-SCS User Manual Download

Page: 14 / 79

3651 WALNUT AVENUE, CHINO CA 91710 • PHONE (909) 664-9980 •

APR-Rework.com

Page

TB-10006 REV December 2018

Employee Owned

Vacuum On-Off

New Removal Profile

Connections

Open/Import Profile

Motion Control

Save/Export File

Glue Remover On-Off

Start Profile

Reflow Blower

Stop Profile

Focus Blower

Auto Profile

Surround Blower

Cycle Advance

Reflow Heater Calibration

Calibration in Progress

Repeat On-Off

Focus Heater Calibration

Screen Capture

Surround Heater Calibration

Open-Close Screen Shot

Thermocouple Calibration

Language Select

Unmounts USB Drive

Back-up & Restore

Software Shutdown

Restore Factory Settings

User Guide

Ethernet Icon

•Each dot corresponds to a different screen. Select a screen by

left-clicking on the appropriate dot.

•The first dot it the title screen, the second dot is the motion control

window, the third dot is thermal profile window, and the fourth dot is the

system configuration window.

System Icons & Descriptions

Navigation

Summary of Contents for APR-2000-SCS
















































































Search results

Summary of Contents for APR-2000-SCS

Reviews:

Related manuals for APR-2000-SCS

Brands by name

Popular brands

APR APR-2000-SCS, User Manual

Search results

Summary of Contents for APR-2000-SCS

Reviews:

Related manuals for APR-2000-SCS

Brands by name

Popular brands