Apprion IONizer 4200 Series Hardware Installation Manual Download Page 11 | Manualshive

Page: 11 / 38

background image

Chapter 1

– IONizer Device Overview

Apprion Proprietary and Confidential

Page 3

Compliance

This equipment has been tested and found to comply with the European Telecommunications Standard
ETS 300 328. This standard covers Wideband Data Transmission Systems referred to in CEPT
recommendation T/R 10.01. This type of equipment is designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed in accordance
with the instruction guide, may cause harmful interference to radio communications.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device must not cause harmful interference and (2) This device must accept any
interference received, including interference that may cause undesired operation.

«
...
9
10
11
12
13
...
»

Summary of Contents for IONizer 4200 Series







































Reviews:

No comments

Related manuals for IONizer 4200 Series

Brand: Cambium Networks Pages: 196

Brand: Cambium Networks Pages: 478

Brand: Cambium Pages: 301

Brand: Cambium Networks Pages: 287

Monitouch V9 Series

Brand: Hakko Electronics Pages: 16

Brand: Arris Pages: 2

Brand: Ruckus Wireless Pages: 3

WG602v3 - Wireless Access Point

Brand: NETGEAR Pages: 122

Brand: Ubiquiti Pages: 16

Brand: Ebyte Pages: 16

Brand: Hantech Pages: 13

Brand: Mach Power Pages: 24

Brand: Airlink101 Pages: 15

Brand: Cambium Networks Pages: 24

Brand: Loopcomm Pages: 75

Brand: Milesight Pages: 19

Brand: EnGenius Pages: 64

Brand: LG Innotek Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands