Applied Membranes AAA-1005 Manual For Installation, Operation And Maintenance Download Page 10

Page: 10 / 16

Installation and Service Manual – Under-the-Counter Point of Use 5 Stage Reverse Osmosis System

Page 10

Mounting the Tank Ball Valve & Connecting the Tank

For this step you will need:

Tank Valve Assembly

Storage Tank

Orange Tubing

Note: Do not tamper with the air valve on the low side of the storage tank. It has been factory charged and
covered with a black cap.

1. Locate the in/out port on the top of the tank. Connect the tank ball

valve by threading onto the fitting. Do not over-tighten.

2. Insert the tubing into the quick connect fitting on the ball valve.

3. Connect the other end of the orange tubing to the tee on the inlet

of the post-carbon filter.

Tank Valve in OPEN Position

Tank Valve in CLOSED

Position

Faucet Installation

For this, step, you will need:

Wrench

Variable speed drill w/

⅛

” and

” drill bits

Faucet Assembly Kit

Yellow Tubing

Summary of Contents for AAA-1005
















Search results

Summary of Contents for AAA-1005

Reviews:

Brands by name

Popular brands

Applied Membranes AAA-1005, Manual For Installation, Operation And Maintenance

Search results

Summary of Contents for AAA-1005

Reviews:

Brands by name

Popular brands