background image

 

ViiA™ 7 Real-Time PCR System

QUICK REFERENCE GUIDE

Note:

For safety and biohazard guidelines, refer to the 

“Safety” appendix in the 

Applied Biosystems ViiA

 

7 Real-

Time PCR System User Guide

 (PN 4442661). For every 

chemical, read the SDS and follow the handling 
instructions. Wear appropriate protective eyewear, clothing, 
and gloves.

In this guide

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

1

Calibrate the ViiA

7 System . . . . . . . . . . . . . . . . . . . . . . . . . . 

2

Perform an experiment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

5

Maintain the ViiA

7 System. . . . . . . . . . . . . . . . . . . . . . . . . . 

15

Power off the ViiA

7 System. . . . . . . . . . . . . . . . . . . . . . . . . 

22

For details on operating and maintaining your ViiA

7 System, refer 

to the 

Applied Biosystems ViiA

 

7 Real-Time PCR System User Guide

 

(PN 4442661). 

Description

The Applied Biosystems ViiA

7 Real-Time PCR System uses 

fluorescent-based polymerase chain reaction (PCR) reagents to 
provide:

 • Quantitative research detection of target nucleic acid 

sequences (targets) using real-time analysis.

 • Qualitative research detection of targets using post-PCR 

(endpoint) analysis.

 • Qualitative analysis of the PCR product achieved by melt curve 

analysis that occurs post-PCR.

Summary of Contents for ViiA 7 Real























Reviews: